Operation; Cutting Height Adjustment; Water Nozzle; Oil Change - Texas A/S 4675 W Bedienungsanleitung

The following cables may be necessary to readjust:
Illustration 7
1. Cable for drive
2. Cable for engine brake
Adjusting the drive cable: Illustration 7A
If you experience slack in the drive cable, this can be
solved simply by tighten or loosen the bolt on the cable.
1. Tighten turning clockwise - loosen the cable.
2. Tighten turning anti clockwise - tighten the cable.
Adjusting the engine brake cable: Illustration 7B
If you experience slack in engine brake cable, this can
be solved simply by tighten or loosen the bolt on the
engine block.

Operation

Always check and refill oil before the start!
Read and apply the instructions given in the
enclosed start guide!
The oil level should always be between min. and max
on the dipstick. Fill with SAE-30 oil. There should be
total 0.6 liter oil in the engine. Use only unleaded 95
octane fuel to the engine. Never overfill the tank.
Start: Never start the mower directly on long grass.
Recoil with primer: Illustration 8
1. Push the primer several times, first time push 1-3
times, if necessary supplement with up to 3-5
times.
Note: It is not possible to drown engine
2. Hold the handlebar for the engine brake; this will
release the engine brake.
3. Pull the recoil starter gently until you feel resistance
in the rope, then pull quickly and energetic. Do not
at any time let go of the recoil starter but slide it
gently into starting position.
4. Hold the bar for self-propelled in order to start
mowing (only self-propelled models).
Note: As long as operating the mower, the bar
forengine brake must be engaged.
Stop:
1. Release the engine brake and self-propelled bar to
turn off the mower and the engine
Note: The blades will still rotate at up to 3 seconds
after stopping.

Cutting height adjustment

See Illustration 9
The lawn mower has 6 different cutting height positions
from 25 mm to 75 mm. The cutting height is adjusted
both on the rear wheels (with the height adjustment
handle) and on the front wheel.
Front wheel adjustment
Pull the support frame down and let the front wheel rest
on it. Dismount the front wheel, and mount it again in
one of the 6 holes as shown on the illuitration.
Fixation of front wheel: Illustration 10
The front wheel can be pivotally, which gives a good
maneuverability, when cutting around flower beds, trees
etc. The direction of the front wheel can also be fixed,
so that it only points forward. Change of postion is done
by pulling the lock and turn it into a new position and
then releasd the lock again, so it falls into position.

Water nozzle

The left side of the mower deck is fitted with a water
nozzle for washing the deck. See Illustration 11.
•
When using the water nozzle, the machine must be
in the lowest height position and placed on the
lawn. This ensures that the water remains under
the deck during cleaning.
•
Attach a hose to the nozzle.
•
Turn on the water and start the engine.
•
The rotations of the blades will ensure that the
water will clean the underside of the deck.
If above instruction is not followed, water may
splash back on the gearbox and clutch cable,
which increases the risk of corrosion and damage
to both parts. This will not be covered by the
warranty!
Note: For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.

Oil change

Oil should be changed for the first time after 5 hours,
then at least 1 time per year.
You will need an oil extractor kit. Art. no. 40-11336
Oil and oil extractor kit is not included
Use an extractor kit and do as follows:
1. Turn on the engine and let it run for 5 min or until
the engine is hot. A hot engine liquefies the oil
which makes it easier to drain.
2. Suck the oil up through the oil filler hole using the
syringe that came with the oil extractor kit. Use the
hose to reach the sump.
3. Transfer the used oil into a empty container.
4. Fill the engine with SAE-30 oil.
5. Check the oil level using the dipstick. (Min / Max)
Remember to dispose the used oil so that it does
no harm to nature. Use your local recycling station.

Air Filter

The air filter should be inspected and cleaned regularly.
If the filter has not been cleaned for a long time, the
engine's power will drop.
See Illustration 12
1. Clean around the air filter before removing the cap.
2. Push the two flaps down and gently pull the cover
3. Carefully remove the paper filter and inspect it.
Brush it with a soft brush. If it is very dirty, replace
it. Be careful that no dirt gets into the inlet.
4. Wash the black foam element in the right side in
warm water and soap.
5. Press the water out of the foam element and let it
dry. Put a few drops of SAE-30 oil on the filter to
moisten it lightly. Carefully squeeze any surplus oil
out of the foam element and reattach.
6. Please note that all parts are assembled correctly
and properly closed, as shown in the picture.
14