Before First Use (Fig. 2) - Scheppach Ab1500X Originalbetriebsanleitung

WARNING
In case of extended working periods, the operating per-
sonnel may suffer circulatory disturbances in their
hands (vibration white finger) due to vibrations.
Raynaud's syndrome is a vascular disease that causes
the small blood vessels on the fingers and toes to
cramp in spasms. The affected areas are no longer
supplied with sufficient blood and therefore appear ex-
tremely pale. The frequent use of vibrating products can
cause nerve damage in people whose circulation is im-
paired (e.g. smokers, diabetics).
If you notice unusual adverse effects, stop working im-
mediately and seek medical advice.
8

Before first use (Fig. 2)

WARNING
Danger of injury!
Do not insert the mains plug into the socket until you
are ready to use the product.
ATTENTION
Product damage!
If the product is operated without lubricating grease or
with too little lubricating grease or with used lubricating
grease, this can lead to product damage.
– Do not use used grease!
– Check the lubricating grease level before each start-
up.
WARNING
Tool attachments may be sharp and become hot during
use. Always wear protective gloves when handling the
tool attachments.
WARNING
Always make sure that the tool attachment is fitted cor-
rectly!
CAUTION
Unsuitable extension cables could be dangerous. There
is a risk of persons being injured due to electric shock.
General information
• The product is delivered with lubricating grease al-
ready filled.
• Proceed with caution. Familiarise yourself with the ap-
plication and possible restrictions, but also with the
specific potential dangers.
• Before connecting of the product, make certain that
the data on the type plate matches with the mains
power data.
• Do not overload the product. Use the correct tool for
your application. The correct tool will do the job better
and safer at the rate for which it was designed.
• Inadequately informed operators can endanger them-
selves and others through improper use. The operator
is responsible for the safety of third parties.
22 | GB
• Check the product regularly for damage.
• Check whether the moving parts function faultlessly
and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of the
electric tool.
• Damaged protective devices and parts must be prop-
erly repaired or replaced by a recognised specialist
workshop, insofar as nothing different is specified in
the operating manual.
• Do not use the product if the switch cannot be
switched on and off. Damaged switches must be re-
placed by our service centre.
• Ensure that the product is always in good condition
and has been properly lubricated.
• The flat chisel (6) or pointed chisel (7) can get stuck
during operation. This allows high forces to be trans-
ferred to the handles. Ensure you have a secure foot-
ing. Hold the product with both hands during the work.
• The integrated vibration damper reduces the vibra-
tions that occur. The handles increase slip resistance
and thus ensure greater safety as well as better grip
and manoeuvrability of the product.
• Always keep the flat chisel (6) and the pointed chisel
(7) sharp.
• Ensure that no there are no electric cables or gas
pipes etc. where you are working and which can lead
to a hazard if damaged when you use the product.
• Place the product on a level, even surface (such that it
cannot topple).
8.1 Adjusting the additional handle (5)
(Fig. 3)
ATTENTION
Only use the product with the additional handle fitted.
Notes:
The additional handle can be rotated 360° on the product
and can be moved to any desired/needed position.
For your safety, the product must only be held by the han-
dle and the additional handle during operation. This pre-
vents electric shock when touching the lines.
1. Turn the handle of the additional handle (5) anticlock-
wise.
2. Position the additional handle (5) in a comfortable and
safe working position for you.
3. Turn the handle of the additional handle (5) clockwise
to tighten it.
8.2 Inserting the tool attachment (6/7)
(Fig. 4)
CAUTION
Keep your hands away from the tool attachment when
the product is in operation.
Note:
Clean the shaft of the tool attachment and grease it light-
ly.
www.scheppach.com