Safety Instructions; Environmental Instructions - Pudu Ccbc02 Benutzerhandbuch

EN
Copyright © 2025 Shenzhen Pudu Technology Co., Ltd. All rights reserved.
No organization or individual shall imitate, copy, transcribe or translate the contents of this user manual, in part or in full,
without the express written consent of Shenzhen Pudu Technology Co., Ltd., or distribute this user manual for profit in any
way (electronically or via photocopying, recording, etc.). The product specifications and information provided in this user
manual are for reference only and are subject to change without further notice. Unless otherwise specified, this user
manual is only intended as a user guide, and no representation shall be deemed as a warranty of any kind.
01

1. Safety Instructions

1.1 Instructions for Electricity
• Do not charge your robot using non-original chargers. If the charger is damaged, replace it immediately.
• Please fully charge the battery to 100% before first use.
• To maximize the efficiency and battery life of the robot, always keep the battery level above 10%.
• A battery level lower than 10% means that the robot will soon run out of power and needs to be charged as quickly as
possible.
• A battery level lower than 2% means that the battery is under protection. In this case, the robot will be unable to perform
tasks and must be charged before it can be used again.
• If the machine is not used for a long time, please turn the power key switch to the "off" position.
• If the robot has not been used for a prolonged time, fully charge it before using it again.
1.2 Instructions for Use
• This auto-cleaning wheeled robot can only be used indoors on flat surfaces. Do not use it outdoors (e.g., on an open
balcony) or on any rugged ground (e.g., stairs).
•  D onotusetherobotatatemperatureabove40℃orbelow0℃.
• If the robot accidentally enters into any incorrect position due to blocking and some other reasons, please suspend the
task promptly and push the robot to the correct route before continuing the task.
• Do not pull the robot while it is working. If you need to push or move the robot, tap on the screen to stop it from moving
first.
• Do not push the robot backward when the power is on.
• Do not block the robot sensor. Otherwise, the robot may fail to move properly or get lost.
• Do not pat the device or press or tap hard on the screen, or damages may be caused.
• Do not use the robot to carry goods. Do not put open-flame stoves or any flammable solid, gas, or liquid on the tray.
• Do not adjust the settings while the robot is moving. Always tap on the screen to pause the robot before proceeding with
any operations.
• Do not clean or maintain the robot when the power is on.
• Cables on the ground should be put away in advance to prevent the robot from dragging them.
• A maximum speed of 1.2 m/s is recommended for safe operation.
• Although the robot features automatic obstacle avoidance, there may be blind spots. Therefore, blocking the robot
abruptly from moving at high speeds may cause accidents.
• When transporting the robot, please make sure that the water in the solution tank and sewage tank is emptied. It is
strictly forbidden to tip the machine during transportation, otherwise, the body may be damaged.
• Robots can use non-foaming, neutral detergents with a pH value of 6 to 8 (defoaming agents can be added). It is
prohibited to use strong acids, strong alkalis and detergents containing active agents.

1.3 Environmental Instructions

• Do not use or charge the robot in a high temperature/pressure environment, areas with fire or explosion hazard, or
other dangerous scenarios to avoid personal injury or robot damage.
• Do not dispose of the robot or its accessories as household waste. Always dispose of the robot and its accessories
according to local laws and regulations, and recycle wherever possible.
• This robot is designed for use on flat surfaces and is not suitable for use in environments with steps or large slopes or
that are too compact.
• It is not recommended to use the robot on heavily greasy ground.
• Put away any wire or other objects on the ground to prevent the robot from being tripped or entangled.
• When using this product on the ground with obvious protrusions (such as thresholds and floor receptacles), make sure
that the height of the protrusions is no more than 8 mm (for cleaning) or 20 mm (for passing through and not for
cleaning).
• The minimal travel width is 70 cm. A width greater than 75 cm is preferred for the robot to move smoothly through a
long passage.
• The maximum possible slope is 8° for the robot (non-cleaning state). To prevent any risks caused by backward slips, the
robot should not be paused when moving uphill.
• The robot only supports cleaning on flat surfaces (in cleaning state), please do not use the robot for cleaning on slopes
visible to the naked eye (greater than 3°).
• Rails or other protective structures should be put in place at the edge of stairs, the entrance of downward slopes, and
other locations where the robot may fall.
02