Air Supply; Lighting The Fire For The First Time - Nordpeis Uno 1, Uno 2, Uno 4, Uno 5 Montageanleitung

Attention! Adjusting the legs affects both the
top and rear connection height.
Flue outlet collar
Uno is delivered standard with a top flue outlet
collar.
Rear connection FIG 4-10
Remove the top plate and use a 5mm Allen key to
release and remove the smoke collar FIG 4.
Loosen the screws holding the brackets for the
back plate FIG 5.
Carefully pull the brackets upwards FIG 6A and pull the
back plate backwards and off FIG 6B.
Remove the cut out in the back plate FIG 7.
Remove the rear smoke outlet cover FIG 8, and place
it over the top outlet FIG 9A. Move the smoke collar on
the back of the product and fasten it FIG 9B.
Put the back plate back in place and tighten the screws
holding it in place FIG 10
Adjusting the door under the combustion chamber,
Uno 4/5
The hinges can be adjusted according to FIG 23
Connecting the flue
Please be aware when connecting the 150 mm flue to
the smoke dome that the flue is placed outside the flue
outlet collar. *Alternative versions exsist due to
National requirements. For the flue connection to the
chimney, follow the recommendations from the chimney
manufacturer

Air supply

For connecting the fresh air supply set see
1, 2 and 4/5.
Placement of CE mark
The CE-mark which is included should be placed on the
stove.
Uno 1: The CE mark should be placed on the
back of the pedestal.
Uno 2: The CE badge should be placed on the
inside of the panel under the door.
Uno 4/5: The CE badge should be placed to the right
in the compartment under the door.
Removing the self closing mechanism FIG 24
The self closing door mechanism connected to the
stove at the bottom left corner. Carefully unhook the
spring and remove the small screw holding the arm
connected to the door. The self closing mechanism is
now deactivated.
.
FIG Uno Air
Ignition air vent control
As an integrated part of the air vent control, Uno has a
ignition air vent control. By pushing the air vent control
rod all the way back (max opening), the ignition air vent
control will be activated.
Attention! After ignition, pull the control back to
normal.
A= Ignition air vent
-

5. Lighting the fire for the first time

When the stove is assembled and all instructions have
been observed, a fire can be lit.
Take care when inserting logs into the burn chamber,
in order not to damage the Thermotte plates. Please
note that there might be some humidity in the insulation
plates which can result in a slower burn rate the first
few times the insert is used. This will be resolved once
the humidity has evaporated. If needed leave the door
slightly open the first 2-3 times the insert is used. It is
advisable to ventilate the room well when using
for the first time as the varnish on the product may
release some smoke or smell. Both the smoke and
smell will disappear and are not hazardous.
Lighting a fire
Insert small, dry pieces of kindling wood, ignite and
ensure the flames have established on the wood
before closing the door. Open the air vent control (FIG
2) before you close the door. Additional ignition air is
obtained by keeping the door slightly open. When the
flames are stable and the chimney is warm, the air
supply is regulated with the air vent control.
When there is a glowing layer of ash, new wood logs
can be inserted. Pull the hot ember to the front of the
combustion chamber when inserting new logs so that
the wood is ignited from the front. Keep the door slightly
open each time new logs are inserted so that the flames
get established. The fire should burn with bright and
lively flames.
Using the insert with low combustion effect and firing
around the clock increase pollution as well as the risk
for a fire in the chimney. Never allow the insert or flue
to become glowing red. Turn off the air vent control
should this happen. Regulation of the air vent control
takes some experience, but after a little while a natural
rhythm for the fire will be found.
GB
A
+
13