Force 5564A Bedienungsanleitung Seite 2

attachment fitted to the tool
—Before using the toot, make sure tiat a shut off device
has been fitted to the air supply Eineand the posiüon is
known and easily accessible so
he toot can be shut off in an emergency.
—Check hose and fifings regularly for wear.
—Take care against entanglement Ofthe moving parb of
the tool wit) clothing, hair, ties. cleaning rags, rings,
jewelry, watches, bracelets. etc. This could cause the
body or parts of the body to be drawn towards and in
contact with the moving parts of the tool and could be
very dangerous.
—It is expected that users will adopt safe working
practices and observe all local, regional and country
legal requirements when installing,
maintaining the tool.
—Take care that the exhaust air does not point towards
any other person or material or substance that could
be contaminated by oil droplets. When first lubricating
a tool or if the tool exhaust has a high oil content, do
not allow the exhaust air to come near very hot
surfaces or names.
—Never lay the tool down until the working attachment
has stopped moving.
—When the tool is not in use, shut off the air supply and
press the triggernever to drain the supply line. If the
tool is not to be used for a period of time, first lubricate,
disconnectfromair supplyand storen a dry average
room temperature environment.
—tf the tool is passed from one user tö a new or
inexperienced user, make sure these instructions are
passed with the tool.
—Do not remove any manufacturer
where fitted, i.e., wheel guards, safety trigger, speed
governors, etc.
—Wherever possible, secure workpiece with clamps, a
vise, etc. to make it rigid so it does not move during
work operation. Keep good balance at all times. Do mt
stretch 05 overreach.
—Try to match the tool to the work operation. Do not use
a tool that is too light or heavy for the work operation. If
in doubt, seek advice.
—tn general terms, this tool
underwater use or use in explosive environtnents
seek advice from manufacturer.
—Try to make sure that the work area is clear to enable
the work task to be performed safely. if practical and
possible, tty to clear unnecessary
starting work.
—Always use air hose and couplings
working pressure ratings
maxinwm working pressure rating of me too}.
Foreseen Use OfThe
This too* designedto be used with flat, reinforced resin 2 718'
diameter ma*mum discs havilÜ a speed rated above 25,000 RPM.
The bore size of tie Gsc 38'.
The tool stwuld not be used with ary otwr type of rating of abrasive
disc or wheel. tt must be used wit' saw
Do not use the too' outside desm
tool any other purpose. or
first seeking advice from the manufactureror an authorized
represerrtaü'æ.
air supply to
using or
fitted safety devices
is not suitable for
—
obstrucöons bebre
with minimum
at least 1 1/2 times the
Tool - 5564A
Of cuttng
intent Never mo&fy the
as a disc cuter,
Page No 2
Work Stations
Thetod sh0Lk:f o nlybe usedas a handheld.hand operatedtool. It iS
alwaysreömærøed mat tool iSused when
600'. tt can be used in other positms, but before any
Qerator must be in a-secure positim ha-vülg firm grip and
and be of the extra safety precautions that must be obSened
when using tie cutter.
Putting Into Service
Air Supply
Use a clean lubricated air supply
pressure at the tool of 90 p.s.iJ6.2 bar when the
with triggernever fully depressed. use recommerded
and length. It is recommended that the tool is cortnected to
soppy as shown in figure I. DO connect
system without an easy 10 reach and operate ait Shut
off valve. The air suppEy should be lubricated.
recommended that an air fitter, regulator, lubricator (FRL) is used
as Shown in Figure 1 as ttis win supply clean. 'Ubicated air at the
correct pressure to the tooE. DetaiFs of such equipment can be
obtained from your supplier. If such equ*xnent is not used, then
thetoolshould beiubricated b y shutting off theairsu»ly to the
tool, depressurizing the line pressing the triggernever on the
tool. Disconnect the air line and pour into the mse adaptor a
teaspoonful (5m)) of a suitable pneumat-c motor lubricatirg
preferably a rust inhibitor. Reconnect tool to air
supply and run tool SEOWIY f or a few seconds to allow air to
circulate the oil. If tool is used frequently, lubricate on daily basis
and if toot starts to skm or lose power.
It is recommended that the air pressure at the toot
is 90 psit6.2 bar.
Operating
The lever (12) otV0tf valve for
sun-ty ensure that the air pressure, measured at me too* iruet
tool not exceed
type and erwure ttEt tie is not cradced or darnaged and that tie
speed of the dsc is in excess ot 25.000 RPM.
*acer (29) suppSed with the tool. M me disc and ti*nen
(30) while holding nut (28). Do mt over Witen as ws could
tie disc. Ensure mat wtWd covet (Z7) iS
the tod with a new or charoed disc,
a protected area. i.e. as urdét a heavy berth, aM run for a
mininynn time of one minute. This wig provide protectm
should break because a Wt mt detected.
Always use eye protection ard wear protec*ive gloves. Remerroer
that the cutting process generate heat and that cut parts,
pamct.narty srnautt8TSt can get very hot and burn fingers if
AlbW parts to cod.
toot and the work process
the use of ear protectors is
dust me use masks is recommended.
rrnterial being will cause termful dust or fumes. If tis is
so, then speciat breathing masks may be required. Seek advü:e
before WOfk.TIE cuttng process will create sparks. Ensure
that these not createa tz_zardto any person, oyect Ofprocess
and are not dire«ed near any flacnrnaye materialsOf fluøs. DOmt
usefre cuter in e.eve uwitocvnents.
Do not apply excessive loads to the tool as this wit reduce the
of the disc. Apply bads toanow the Mieel to wt. Try
a}ways to keep (Ec sware to me cut. Do mt apply side Eoadsor
on the ot the
is carefuøy ewnine the
necessary. Start tool as if
undet a berm Makesure Objectto be ground
on a solid
use, the
wilt give a measured air
is tunning
hose size
air
the too} to me air line
Et is Strongly
Oil
the tool is
tod. Connect to a sunaue air
PSIG}6.2 bar. -Setect disc
onty the
*Ce. WPM first
shwld first be started in
tie M•.eet
create a noise level that
C,LJüäig p rocess wil create
that the
cutter with care. the cutter
$0' darnage and replace if
first time Of a disc, i.e.
in •a firm fixed