bbluv Basa Bedienungsanleitung Seite 3

*For some sensitive people, nausea may occur when mouth
temperature is measured.
*After measuring rectal temperature, there may be a slight
feeling of distension in the anus. These are all normal
phenomena, and a rest may relieve them. If you are
concerned that the measurement cannot be done correctly,
please consult a professional physician for the measurement.
*To obtain more accurate measurement data, it is
recommended to measure the oral and rectal temperature
in direct mode.
4. Under the adjusted mode, after the thermometer detects
the temperature of the human body, the measurement results
will be displayed about 8s later with a prompt sound.
8 seconds
In direct mode, when the temperature value of human body
is stable or the test time reaches 5min, the thermometer will
display the measurement result with prompt sound.
Up to 5
minutes
5. Remove the battery of the thermometer and power it on
again each time. The Adjusted mode is entered by default for
the next measurement.
THE MODE SWITCH :
1. In the off state, long press the "power key" button, then it will
automatically enter the measurement state different from
that used last time.
2. If the adjusted mode was used last time, it will automatically
change todirect mode and start temperature measurement.
Long press the "power key" button
If the direct mode was used last time, it will automatically
change to adjusted mode and start temperature
measurement.
Long press the "power key" button
DISPLAY AND SOUND TIPS :
After the measurement is completed, the following tips may
appear in the thermometer:
Sound tips
Screen display
Temperature:
32.00°C -37.59°C
(89.60 °F-99.67 °F)
4
Loosen
Loosen
Representation
of information
Target temperature
"beep"~
values for this
measurement
"beep beep
Temperature:
beep"..."beep beep
37.60°C ~42.90°C
beep"..."beep beep
(99.68 °F 109.22 °F)
beep"..."beep beep
beep"..."beep beep
beep"
"beep "..."beep"...
Err
"beep"..." beep"
"beep "..."beep"...
Hi
"beep"..." beep"
"beep "..." beep"
Lo
POWER OFF FUNCTION :
If the thermometer does not perform any operation within 30
seconds or press "power key" again, it will enter the shutdown
state directly.
TEMPERATURE UNIT SETTING FUNCTION :
1.When the thermometer is off, hold down "power key" and
do not release it. The product will start. Wait for 5 seconds
after the screen turns off, and then enter the temperature unit
setting interface
Hold the "power key"
2. Hold down the "power key" and do not release it. The unit
of °C or °F will be automatically switched,every 2s. When the
required unit is displayed, release the hand, that is, select the
current unit, and the thermometer immediately enters the
state to be measured.
Automatically
switches
every 2s
LOW VOLTAGE PROMPT FUNCTION :
1. The thermometer automatically detects the battery
voltage every time it is turned on. When the battery voltage is
insufficient but can continue to use, the "
on the display screen, but does not affect the operation.
2. When the battery voltage is too low to continue to use, the
display screen appears separately "
about 8 s after forced shutdown, thermometer need to
replace the new battery to continue to use.
INITIALIZATION FUNCTION :
Remove the battery and repower the thermometer, and it will
automatically restore to the factory setting.
BODY TEMPERATURE :
The normal body temperature of people is a range value, the
Target temperature
values for this
measurement
Anormal temperature
rise rule
(e.g., measurement
process shedding)
The measurement
temperature is higher
than the maximum
value of the
thermometer range
The measured
temperature is below
the minimum value of
the thermometer range
Let go of
"power key"
" icon appears
" icon and flashes,
5