AMiO HB-ZN04 Benutzerhandbuch

EN
EN - USER MANUAL
Digital battery charger HB-ZN04/ 02088
Read the operating instructions carefully before use!
Save them for future reference!
SAFETY INSTRUCTIONS:
• During the charging process, explosive gases may be produced.
Do not use open fire and ensure appropriate ventilation during
the charging process.
• Never attempt to charge a frozen battery.
• Never charge the battery when the engine is running.
• Do not use the appliance in damp or wet areas. Do not expose
the appliance to rain.
• When not in use, store the appliance in a dry place out of the
reach of children.
• Keep children and onlookers at a safe distance when the
appliance is in use. Keep children under supervision to make
sure they do not play with the appliance.
• Check the appliance to see if any parts are damaged. Do not
use the appliance if it is damaged or not working properly, or if
the power cord or plug are damaged. Take the appliance to an
authorized service center to be checked, repaired or adjusted.
• Do not attempt to charge dry cell batteries with the appliance,
they can explode and cause fatal or personal injury, and/or
material damage.
• The appliance is only intended for charging/auxiliary starting of
6V or 12V batteries.
• It is not intended to be used to supply power to low voltage
systems.
• Do not attempt to open the battery charger – risk of electric
shock.
• Switch off the appliance and unplug the power cord when it is
not in use.
• The manufacturer shall not be liable for any damage caused by
the failure to use the battery charger in accordance with this
manual.
FIRST AID:
Eyes: If you get battery fluid in your eyes, rinse with water for at least
15 minutes and seek medical attention immediately.
Skin: If you get battery acid on your skin, rinse immediately in plenty
of fresh water and wash thoroughly with soap and water. Seek
medical attention if redness, pain or irritation persists.
TECHNICAL PARAMETERS:
• Input voltage: AC 220-240V
• Output voltage: DC 6/12V
• Maximum charging current:
motorcycle mode: 2A +/-10%
car mode: 4A +/-10%
• Protection class: IP65
CONTROL:
1. Mode change button
2. Voltage display
3. 6V batteries charge mode
4. Cold mode for temperatures below 0ºC
5. 12V batteries charge mode
6. Charging with 4A current, which is used for larger capacity bat-
teries, e.g. cars, boats
7. Charging with 2A current, which is used for low-capacity batter-
ies, e.g. motorcycles, snowmobiles, quads, etc.
8. Icon showing the progress of the battery charge
Charging modes:
Battery voltage 6V capacity below 14Ah ambient temper-
ature above 0ºC – FULL 7,2V
Battery voltage 6V capacity below 14Ah ambient tem-
perature below 0ºC – FULL 7,4V
Battery voltage 12V capacity below 14Ah ambient tem-
perature above 0ºC – FULL 14,3V
Battery voltage 12V capacity below 14Ah ambient
temperature below 0ºC – FULL 14,7V
Battery voltage 12V capacity above 14Ah ambient tem-
perature 0ºC – FULL 14,3V
Battery voltage 12V capacity above 14Ah ambient
temperature 0ºC – FULL 14,7V,7V
Examples of display indications:
Incorrect connection to the battery, check the pole connection.
Red „+" black „-". The error will also appear if the battery is deeply
discharged or damaged.
Correct connection, the display shows the battery voltage
Battery fully charged
USE:
• Before the use of the charger is started, it is absolutely essential
to check its technical condition. Check the condition of the
connecting cables and the plug - if their damage is observed,
replace the damaged element. Check the condition of the
housing - if it is damaged, the housing must be subjected to
detailed inspection carried out by an authorized professional.
• Check that the mains voltage corresponds to the rated voltage
on the type plate. If you are using an extension cord, the cross-
sectional area of the wires must have the correct rating for the
power supply to the appliance.
• Before starting the battery charging, it is absolutely essential to
disconnect the battery from the installation in which the battery
is used. Use the guidelines for the battery charging, included in
the manual for the car or other equipment.
• Slacken or remove the plugs from the respective battery sections (if
they are present), check the acid level in the battery and if necessary,
fill it up with decriminalized water.
• Connect the charger red clamp to the end of positive pole of the
battery „+", and the black clamp to the negative pole „-". Place the
charger at the maximum distance from the battery, then connect
the charger to the power source, using the power cord.
• Charging begins after connecting the power cable to a power
source. The display shows the current battery voltage. When the
charger indicates that the battery is fully charged (FULL on the
display), disconnect the charger from the power supply, remove
P/N: 02088
1