Appendix A; Profibus Dp-V0 Gsd Profile Document - Eaton Pmint Installation Und Betrieb

04/10 AWB1230-1621
Effective April 2010

Appendix A

PROFIBUS DP-V0
;==============================================
; GSD File for Eaton Low Voltage Circuit Breakers
;
; English Version 1 .0
; Date: 2009-02-03
; revised by CC-TDH/P . Thiessmeier
; Changes:
; support of mandatory profile 1 (F0)
; changed to modular slave for better support of intel-based plcs
; Date: 2009-02-17
; revised by A .A . Anderson
; Changes:
; User_Prm_Data_Len = 3, to eventually support DP-V1
; Added Unit_Diag_Bit(0024-0052)
; Date: 2009-06-04
; revised by A .A . Anderson
; Changes:
; Added Module = "Add . Data of profile type 4" 0xDE
; Date: 2009-06-29
; revised by A .A . Anderson
; Changes:
; Comments (Slave related Key Words) Only
;==============================================
#PROFIBUS_DP
;
;==============================================
;General parameters
;==============================================
GSD_Revision = 3
Vendor_Name = "Eaton Corporation"
Model_Name = "Magnum,IZM,NRX" ;"Low Voltage Circuit Breaker"
Revision = "V1 .0" ;Revision version of device
;Revision_Number = ;Must agree with RevNum in slave-specific diag
Ident_Number = 0x0BF4
Protocol_Ident = 0 ;0=PROFIBUS DP
Station_Type = 0 ;0=DP Slave
FMS_supp = 0 ;0=Not FMS/DP mixed device
Hardware_Release = "V1 .0" ;Hardware release of device
Software_Release = "V1 .0" ;Software release of device
9 .6_supp = 1
19 .2_supp = 1
31 .25_supp = 0
45 .45_supp = 1
93 .75_supp = 1
187 .5_supp = 1
500_supp = 1
1 .5M_supp = 1
3M_supp = 1
8
EATON CORPORATION www.moeller.net/en/support
GSD Profile Document
PMINT—PROFIBUS DP translator
6M_supp = 1
12M_supp = 1
MaxTsdr_9 .6 = 60 ; Bit Time
MaxTsdr_19 .2 = 60 ; Bit Time
MaxTsdr_31 .25 = 60 ; Bit Time
MaxTsdr_45 .45 = 60 ; Bit Time
MaxTsdr_93 .75 = 60 ; Bit Time
MaxTsdr_187 .5 = 60 ; Bit Time
MaxTsdr_500 = 100 ; Bit Time
MaxTsdr_1 .5M = 150 ; Bit Time
MaxTsdr_3M = 250 ; Bit Time
MaxTsdr_6M = 450 ; Bit Time
MaxTsdr_12M = 800 ; Bit Time
Redundancy = 0 ;0=Redundant Xmission NotSupported
Repeater_Ctrl_Sig = 2 ;CNTR-P bus signal:
; 0=NotConnected, 1=RS485 2=TTL
24V_Pins = 0 ;M24V & P24V bus signals:
; 0=NotConnected, 1=Input, 2=Output
Implementation_Type = "SPC3" ;Optional
;Bitmap_Device = "DIB_????" ;Optional
;Bitmap_Diag = "DIB_????" ;Optional
;Bitmap_SF = "DIB_????" ;Optional
;==============================================
;Physical Interface parameters (optional)
;==============================================
;Physical_Interface = 0 ;Optional RS485-intrinsic
;Transmission_Delay_9 .6 = 0 ; Bit Time
;Transmission_Delay_19 .2 = 0 ; Bit Time
;Transmission_Delay_31 .25 = 0 ; Bit Time
;Transmission_Delay_45 .45 = 0 ; Bit Time
;Transmission_Delay_93 .75 = 0 ; Bit Time
;Transmission_Delay_187 .5 = 0 ; Bit Time
;Transmission_Delay_500 = 0 ; Bit Time
;Transmission_Delay_1 .5M = 0 ; Bit Time
;Transmission_Delay_3M = 0 ; Bit Time
;Transmission_Delay_6M = 0 ; Bit Time
;Transmission_Delay_12M = 0 ; Bit Time
;Reaction_Delay_9 .6 = 0 ; Bit Time
;Reaction_Delay_19 .2 = 0 ; Bit Time
;Reaction_Delay_31 .25 = 0 ; Bit Time
;Reaction_Delay_45 .45 = 0 ; Bit Time
;Reaction_Delay_93 .75 = 0 ; Bit Time
;Reaction_Delay_187 .5 = 0 ; Bit Time
;Reaction_Delay_500 = 0 ; Bit Time
;Reaction_Delay_1 .5M = 0 ; Bit Time
;Reaction_Delay_3M = 0 ; Bit Time
;Reaction_Delay_6M = 0 ; Bit Time
module—installation and use