Eaton PMINT Installation Und Betrieb Seite 11

PMINT—PROFIBUS DP translator
module—installation and use
Table 15. Cause-of-Status Code Definitions
Code Definition
0 Unknown
1 Normal operating mode
2 External condition #1
3 Instantaneous phase
overcurrent
4 Instantaneous ground
overcurrent
5 Instantaneous neutral
overcurrent
6 Instantaneous residual
overcurrent
7 Phase inverse-time
overcurrent
8 Ground inverse-time
overcurrent
9 Neutral inverse-time
overcurrent
10 Residual inverse-time
overcurrent
11 Overvoltage
12 Undervoltage
13 Auxiliary overvoltage
14 Auxiliary undervoltage
15 Underfrequency
16 Overfrequency
17 Current unbalance
18 Voltage unbalance
19 Apparent power factor
20 Displacement power factor
21 Zone interlock phase
22 Zone interlock ground
23 Watt
24 VA
25 VAR
26 Power demand
27 VA demand
28 Var demand
29 Current demand
30 Total harmonic distortion
31 Operations count
32 Contact maintenance
33 Control via communications
34 Contact disagreement
35 Breaker failure
36 Operation time exceeded
37 Coil supervision
38 Programmable logic
39 Diagnostic warning #1
Code Definition
40 Diagnostic failure #1
41 Low battery
42 Multiple causes
43 Diagnostic warning #2
44 Diagnostic warning #3
45 Diagnostic warning #4
46 Diagnostic warning #5
47 Diagnostic warning #6
48 Diagnostic warning #7
49 Diagnostic warning #8
50 Diagnostic warning #9
51 Diagnostic warning #10
52 Diagnostic failure #2
53 Diagnostic failure #3
54 Diagnostic failure #4
55 Diagnostic failure #5
56 Diagnostic failure #6
57 Diagnostic failure #7
58 Diagnostic failure #8
59 Diagnostic failure #9
60 Diagnostic failure #10
61 Long delay phase overcurrent
62 Short delay phase overcurrent
63 Fixed instantaneous phase overcurrent #1
64 Bad/missing rating plug
65 Reverse power
66 Fixed instantaneous phase overcurrent #2
67 Reverse phase
68 Reverse sequence
69 Phase current loss
70 Phase voltage loss
71 Alarm active
72 Bad frame
73 Phase currents near pickup
74 Lockout
75 Making current release
76 Fixed instantaneous phase overcurrent #3
77 Set points error
78 Overtemperature
79 Accessory bus
Cause-of-Status Code Definitions (continued)
Code Definition
80 Long delay neutral overcurrent
81 External condition #2
82 Historical data
83 External condition #3
84 Ground fault (instantaneous or delay)
85 Earth fault (instantaneous or delay)
86 External condition #4
87 External condition #5
88 External condition #6
89 External condition #7
90 External condition #8
91 External condition #9
92 Multiple external conditions
93 Motor bearing temperature
94 Load bearing temperature
95 Auxiliary temperature
96 Winding temperature
97 Local temperature
98 External temperature
99 Rolled phase
100 Per unit voltage
101 Sensitive
102 De-energize
103 Non sensitive
104 Time delayed sensitive
105 Breaker pumping
106 Sub-network malfunction
107 Learning
108 Offline
109 Test
110 Jam
111 Underload
112 Delay ground overcurrent
113 Calibration
114 Emergency
115 Torque limit
116 Deceleration
117 Voltage sag
118 Voltage swell
119 Programming error
120 Failed to sync on phase
121 Failed to sync on frequency
EATON CORPORATION www.moeller.net/en/support
04/10 AWB1230-1621
Effective April 2010
Code Definition
122 Failed to sync on voltage
123 Anti-backspin
124 Zero speed
125 Time between starts
126 Source 1
127 Source 2
128 Start
129 Manual
130 Synchronizing
131 Starts per hour
132 Preferred source
133 Plant exerciser
134 Neutral ground overvoltage
135 Safety interlock
136 Real-time clock
137 High floating voltage
138 Trip blocked
139 Incomplete sequence
140 Cause N/A (none)
141 Trip position
142 Voltage transient
143 Tamper
144 RTD
145 Differential
146 Frequency out of range
147 Sensor mismatch
148 Check aux. switch
149 Overcurrent
150 Time delayed Watt-VAR
151 Overcurrent Watt-VAR
152 Power
153 Maintenance Mode
154 Breaker mechanism fault
155 Automatic reclose lockout
156 Disconnect position
157 Shunt fault problem
Reserved 158 ... 2043
2044 Product specific code 2044
2045 Product specific code 2045
2046 Product specific code 2046
2047 Product specific code 2047
11