Fast Search - Thomson Roc1105Pan Bedienungsanleitung

INPUT
LINK
EXIT
INDEX
ASPECT
AAA
Replacement Remote for 2. Package Contents
PANASONIC SERIES: TV/LCD/LED/HDTV • Replacement Remote Control
• 2x AAA Batteries
• This operating instructions incl. Code List
3. Safety notes
• Do not use the Universal Remote Control in
Thank you for your decision for a Thomson product.
moist or wet environments and avoid spray-
Take your time and read the following instructions
water contact.
and information completely. Please keep these
• Do not expose the Universal Remote Control
instructions in a safe place for future reference.
to heat sources or direct sunlight.
This remote control can by default control 90%
• Do not drop the Universal Remote Control.
models of PANASONIC brand, there´s no need to
• Never open the Universal Remote Control. It
set it up. lf the remote doesn't work, please choose
contains no user-serviceable parts.
one of the setup methods described in chapter 5.
• As with all electrical devices, keep the
Universal Remote Control away from
The keys
children.
1. Power TV ON/OFF
2. Turn your TV sound ON/OFF
3. TV Mode
Warning
4. AV Mode
5. APPS
• When inserting batteries, note the
6. LINK
correct polarity (+ and - markings) and
7. Program Guide
insert the batteries accordingly. Failure to
8. Tools menu
do so could result in the batteries leaking
9. HOME
or exploding.
10. Menu
• Do not short-circuit batteries.
11. Exit Menu
• Do not charge batteries.
12. Internet
• Do not throw batteries in a fire.
13. SD/USB Mode
14. Option and Tools • Keep batteries out of the reach of
15. Back key children.
16. Enter
• Do not allow children to change batteries
17. Use when watching TV to see what´s on
without supervision.
other channels or to highlight/select On-
• Remove the batteries from products
Screen options
that are not being used for an extended
18. Use to select a variety of on screen options
period.
19. Volume + / -
20. Program +/-
4. Getting started – installing the Batteries
21. Teletext ON/OFF
22. Teletext Subtitle
23. Teletext Info Note
24. Teletext Hold
25. Numeric keys 0 – 9 to enter channel numbers
• Use 2 AAA batteries
26. Access to 2- or 3-digit channel numbers
• Remove the battery cover from bottom
27. Previous Channel
of remote.
28. Info
• Check the +/- polarity on the batteries
29. Normal
and inside the compartment.
30. Picture Size
• Insert the batteries.
31. Goes backward (DVD, BlueRay ... )
• Slide the battery holder back into the
32. Play a disc (DVD, BlueRay ... )
remote until the clips locate.
33. Fast Forward (DVD, BlueRay ...)
34. Player Preview (DVD, BlueRay ...)
35. Player Next (DVD, BlueRay ...)
Note – Code Memory
36. Suspends play and stops on an image
(DVD, BlueRay...)
37. 3D Mode ON/OFF This remote control saves the settings during
38. Stop the disc (DVD, BlueRay ... ) battery change.
39. Record
5. Setup
1. Explanation of the Note and Warning
symbol This remote control can by default control 90%
models of PANASONIC brand, there´s no need
to set it up. lf it doesn't work, please choose
Warning
one of the following setup methods 5.1 or 5.2.
This symbol is used to indicate safety instructions or
5.1 INPUT CODE
to draw your attention to specific hazards and risks.
CODE List:
001, 002, 003, 004, 005, 006, 007, 008,
Note
009, 010, 011, 012, 013
This symbol is used to indicate additional
information or important notes.
2
1. Press and hold the key [MUTE] and 6. Maintenance
[POWER] until the LED will be lit,
• Do not mix new and used batteries for
then release keys.
powering the Universal Remote Control, as
old batteries tend to leak and may cause
power drain.
• Do not use corrosive or abrasive cleansers on
your Universal Remote Control.
• Keep the Universal Remote Control dust free
2. Enter the three codes from code Iist.
by wiping it with a soft, dry cloth.
When the code input is finished, the
LED will turn off.
7. Troubleshooting
Q. My Universal Remote Control does not
work at all!
A. Check your TV. If the TV main switch is
turned off, your Remote cannot operate
your TV.
LAST
A. Check whether your batteries are inserted
properly and are in the correct +/- position.
3. Please try to use the remote control.
A. Check whether you have pressed the
lf it doesn't work well, please try other
corresponding device mode key for your
codes: [002], [003], [004] ...
device.
A. If the batteries are low, replace the
batteries.
Note
Q. My TV responds only to some of the
commands.
lf the code is invalid, the LED flashes twice
A. Try other codes until most keys work
and then lights up permanently. To exit the
properly.
setup, please press [MUTE].
8. Warranty Disclaimer

5.2 FAST SEARCH

The manufacturer assumes no liability and
1. Press and hold the key [MUTE] and
provides no warranty for damage resulting
[POWER] until the LED will be lit, then
from improper installation/mounting, improper
release keys.
use of the product or from failure to observe
the operating instructions and/or safety notes.
9. Service and Support
Please contact Hama Product Consulting if you
2. Press the key [ CH+]. Each time you
have any questions about this product.
press, the remote will search once.
Hotline: +49 9091 502-115 (German/English)
When the code changes, you can test
Further support information can be found here:
if [POWER], [VOL+],[MENU],[0-9] keys
www.hama.com
work well. If ok ,please press [ MUTE] to
save the code and exit. 10. Recycling Information
Note on environmental
3. lf it doesn't work well, repeat the fast
protection:
search by pressing [ CH+].
After the implementation of the
European Directive 2012/19/EU and
5.3 CODE INQUIRY
2006/66/EU in the national legal
Use the following method to find out which system, the following applies: Electric and
code is currently set: electronic devices as well as batteries must not
be disposed of with household waste.
1. Press and hold [MUTE], then press
Consumers are obliged by law to return
[POWER] until the LED will be lit, then
electrical and electronic devices as well as
release keys.
batteries at the end of their service lives to the
public collecting points set up for this purpose
2. Input [9].[9].[0] with number keys. The
or point of sale. Details to this are defined by
LED will flash twice and goes off.
the national law of the respective country. This
3. Press the number key 1 for the 1st digit
symbol on the product, the instruction manual
of the code. The LED will start to flash.
or the package indicates that a product is
Count the LED flashes. The number of
subject to these regulations. By recycling,
flashes resemble the code's first digit.
reusing the materials or other forms of utilising
Repeat this procedure for the 2nd and
old devices/Batteries, you are making an
3rd digit of the code:
important contribution to protecting our
2nd digit -> enter 2 -> count LED
environment.
flashes
3rd digit -> enter 3 -> count LED flashes
lf code number is [0] the LED will not
flash.
5.4 Compatible Remote Control Model
Due to too many Remote Control models, we
only Iist some of them below. lf your remote
control is similar to the drawing, the replacement
remote can control your TV (Page 38).
3