CMT ORANGE TOOLS CMT12 Betriebsanleitung Seite 8

EN
SPECIFICATIONS & USE
CMT12
Power input
No load speed
Collet
Routing depth
Tool weight
•
These data are valid for nominal voltages of 220~240 V ~ 50/60 Hz. Values
may vary if the voltage is lower.
• Due to ongoing research and development, specifications are subject to
change without prior notice.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE!
1 - INTENDED USE
The tool is intended for flush trimming and profiling of wood,
plastic and similar materials.
2 - POWER SUPPLY
The tool should be connected only to a power supply of the
same voltage as indicated on the nameplate.
The trimmer can only be operated on single-phase AC supply.
It is double insulated in accordance with European Standard
and, therefore, can also be used with power sockets that are
not grounded.
3 - SAFETY TIPS
For your own safety, please refer to enclosed safety instructions.
4 - TRIMMER SAFETY WARNINGS
1. Hold the trimmer only by the insulated handles, as the
cutting tool may come into contact with its own power
cord. Cutting a live wire can make exposed metal parts of
the power tool live as well, potentially causing an electric
shock to the operator. Keep the handles dry, clean, and
free from oil and grease.
2. Use clamps or other practical methods to secure and
support the workpiece on a stable platform. Holding the
workpiece by hand or against your body makes it unstable
and may result in a loss of control.
3. Use personal protective equipment.
4. Handle the bits very carefully. Use protective gloves.
5. Never use a damaged, defective (or suspected defective),
incomplete, excessively worn, or poorly sharpened tool.
6. Use cutting tools with a shank size compatible with the
power tool.
7. Avoid cutting nails. Inspect the workpiece carefully and
remove all nails before operation.
8. Hold the trimmer firmly during use.
9. Keep hands away from rotating parts.
10. Make sure the bit does not come in contact with the work-
piece before switching power on.
11. Before using the tool on an actual workpiece, let it run for
8
W 710
min 10.000-30.000
-1
mm 6-6.35-8
mm 0-40
Kg 1.9
a while. Watch for vibration or wobbling that could indicate
an improperly installed bit.
12. Ensure that the rotation direction of the cutting tool
matches the feed direction. Do not exceed the maximum
RPM (MAX RPM) specified.
13. Do not leave the tool running. Operate the tool only when
hand-held.
14. Always switch off and wait for the bit to come to a com-
plete stop before removing the tool from the workpiece.
15. Do not attempt to touch the bit immediately after opera-
tion; it may be extremely hot and could burn your skin.
16. Always lead the power supply cord away from the tool to-
wards the rear.
17. Do not use solvents, gasoline, oil or similar liquids to
clean. Doing so may cause cracks in the trimmer.
18. Some materials contain chemicals that may be toxic.
Avoid inhaling dust and contact with the skin. Follow the
safety instructions provided by the supplier of the material
you are working with.
OPERATING
INSTRUCTIONS
Do not let comfort or familiarity with this trimmer (gained from
repeated use) replace strict adherence to safety rules for the
subject product.
Misure or failure to follow the safety rules indicated in this
instruction manual may cause serious personal injury.
Always be sure that the trimmer is switched off and unplugged
before carrying out any adjustments or maintenance on the
5 - ADJUSTING BIT PROTRUSION
To adjust the bit depth, open the locking lever and move the
base up or down as needed by turning the adjustment screw.
After making the adjustment, securely close the locking lever to
fix the base in place (FIG. 1).
NOTE:
When the trimmer base does not lock even with the locking
lever closed, tighten the nut, then close the locking lever.
6 - SWITCH ACTION
Before plugging in the tool, always be sure that the tool is
switched off (pos. "0").
--- --- ---
To start the tool, move the switch (FIG. 2) lever to the "I" (ON)
position.
To stop the tool, move the switch (FIG. 2) lever to the "0" (OFF)
position.
www.cmtorangetools.com
WARNING:
CAUTION:
tool.
CAUTION: