Bosch GKM 18 V-LI Professional Originalbetriebsanleitung Seite 16

OBJ_BUCH-2231-001.book Page 16 Tuesday, November 18, 2014 3:22 PM
16 | English
5 Hex key
6 Lock-off button for On/Off switch
7 On/Off switch
8 Battery unlocking button*
9 Battery pack*
10 Clamping lever for cutting-depth preselection
11 Motor housing
12 Cutting mark, 0°
13 Base plate
14 Parallel guide*
15 Handle (insulated gripping surface)
16 Clamping bolt with washer
17 Clamping flange
18 Saw blade*
19 Mounting flange
20 Saw spindle
21 Retracting blade guard
22 Lever for retracting blade guard
23 Set of screw clamps
24 Button for charge-control indicator*
25 Battery charge-control indicator*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw
Article number
Rated voltage
No-load speed
Max. cutting depth
– at mitre angle 0°
Spindle lock
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
**
– during operation and during
storage
Recommended batteries
Recommended chargers
* depending on the battery pack being used
** Limited performance at temperatures <0 °C
1 609 92A 0PX | (18.11.14)
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-5.
Typically the A-weighted sound pressure level of the product
is 75 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
determined according to EN 60745:
Sawing metal: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
GKM 18 V-LI
Declaration of Conformity
3 601 FA4 0..
V= 18
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
-1
min 4250
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
mm 50
the following standards: EN 60745-1, EN 60745-2-5.

Technical file (2006/42/EC) at:
mm 105 x 200
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
mm 136
Henk Becker
mm 130
Executive Vice President
mm 2.0
Engineering
mm 2.5
mm 1.2
mm 20
Robert Bosch GmbH, Power Tools Division
kg 2.6/2.7*
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 18.11.2014
°C 0...+45
Assembly
°C –20...+50
Battery Charging
GBA 18V ...
 Use only the battery chargers listed on the accessories
AL 18..
page. Only these battery chargers are matched to the lith-
GAL 3680
ium-ion battery of your power tool.
(triax vector sum) and uncertainty K
h
2 2
<2.5 m/s , K=1.5 m/s .
h
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools