Genius ROTORAZER 8 in 1 Übersetzung Der Originalanleitung Seite 13

1 x Li-Ion Battery 1500mAh (2)
1 x Charger (3)
1 x Hand Support (4)
1 x Big baffle (5)
1 x Small baffle (6)
2 x Plastic blade (7)
1 x Nut driver (8)
1 x Anti-collision frame (9)
1 x Pair of wheels (10)
1 x Cover (11)
1 x Wrench (12)
2 x Grass Cutting rope (13)
1 x Screwdriver (14)
1 x Screw (15)
1 x Instruction manual
3. INSTRUCTIONS FOR USE
How to install batteries
Always be sure that the machine is switched
off before manipulating the battery.
Always hold the machine and the Battery firmly
when installing or removing them.
After charging the Battery (2) with the Char-
ger (3) for a minimum of 180 minutes, simply
align the Fast Mower by Rotorazer's battery
terminals (at the handle) to the grooves of the
Battery. Slide the Battery through all the way
towards the machine until a click sounds to
lock (Image A).
How to remove batteries
Always be sure that the machine is switched
off before manipulating the battery.
Always hold the machine and the Battery firmly
when installing or removing them.
To remove the Battery (2), push down on the
red button of the Battery and pull out by sliding
it off away from the machine (Image B).
IMPORTANT: The product must be assem-
bled without the battery installed.
How to use
Assembling the Small Baffle
Use the Small Baffle (6) when you don't need
to use the wheels (10). Wheels can only be
used with the Big Baffle (5).
1- Unscrew and take out the top of the cover
(11) (Image C).
2- Align the Small Baffle (6) into the slots with the
same shapes (Image D) and press until the Small
Baffle enters completely into the cover.
3- Once fully entered, rotate the Small Baffle (6)
until the Small Baffle's circle hole stays at the top
(Image E).
4-Place the screw (15), as shown in (image E'),
and screw it in with the screwdriver (14) so that
both parts are correctly fastened.
5- Put back the top cover (11) over the plate
(Image F).
6- To install the blades, please go to the "As-
sembling Blades" section.
Assembling the Big Baffle & Wheels
Use the Big Baffle (5) when you need to use the
wheels (10). Wheels can only be used with the
Big Baffle (5).
1- Unscrew and take out the top cover (11) (Image
C).
2- Introduce the long screw on the external side
of each of the wheels (Image G).
3- Place the nut on the inner area of the Big
Baffle (5) and align the long screw of the wheel
with it, and screw them together with the help
of the Wrench (12) (Image H).
Note: There are three holes on each side of
the wheels: please choose the desired hole
depending on desired height for the wheels
(Image I).
4- Once the wheels are assembled, align the
Big Baffle (5) into the slots with the same sha-
pes and press until the Big Baffle enters com-
pletely into the cover. Once fully entered, rotate
the Big Baffle (5) until the circle hole stays at
the top (Image J).
5- Place the screw (15), as shown in image S,
and screw it in with the screwdriver (14) so that
both parts are correctly fastened.
6- Put back the top cover (11) over the plate (Ima-
ge K).
7- To install the blades, please go to the "As-
sembling Blades" section.
Assembling Blades
All the blades can be assembled on both the
Big baffle (5) and Small baffle (6).
PLASTIC BLADE (7):
Suitable for lawn mowing.
Sizes: 15 x 3,3 cm
Cutting depth: 5 cm
GRASS CUTTING ROPE (13)
Suitable for new growth & soft grass
Sizes: 15 x 3,3 cm
Cutting depth: 5 cm
PLASTIC BLADE
1- Unscrew the top cover's screw, then align
the Plastic blade (7) with the top cover's hole,
and place the screw above of it (Image L).
2- Hold the top cover by hand and tighten the
screw with the Nut driver (8) (Image M). To re-
move simply reverse the steps.
GRASS CUTTING ROPE
1- Unscrew the top cover's screw, then align
the Grass Cutting Rope (13) with the top
cover's hole, and place the screw above it.
13