Lutron Homeworks HW-RPM-4R Installationsanleitung Seite 2

II. For any feed circuit
shorted load and resolve the wiring problem before pro-
ceeding
12. Turn circuit breaker(s)
two position bypass jumpers for possible later use.
Caution • Bypass jumpers must be reused whenev-
er a circuit breaker
Damage caused by short circuits and miswiring IS
NOT COVERED by the product warranty.
Secure the module's
13.
blocks using 3.5 to 5 in-lbs. (.4-.55 Nm) of torque.
Attention: Install the Control Hot (CH) on the Circuit I
Hot and Control Neutral (CN) on the Circuit 1 Neutral
as shown in Figure 3.
14. Mount the module into the rough-in
in Figure 1. Do not overtighten screws, torque to 20 in-
lbs (2 25 Nm)
Set the address switch to match the module's position
15.
as shown in Figure I. See Figure 4 for address switch
function settings.
Plug in the control harness as described in the HW-
16.
PM, HWl-PM-D48 or HWI-MI installation
17. Replace panel cover and turn the input circuit break-
er(s) ON.
After the processor is configured, check each mod-
18.
ule's diagnostic LED (Light Emitting Diode)
LED Status
Off No Power
1 blink per sec Normal Operation "Heartbeat"
Not communicating
control harness; module receiving invalid
1 blink per 7
load type; module set on invalid or
seconds
diagnostic address; system not properly
"Lighthouse"
configured or addressed
software
World Headquarters and Technical
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
TOLL FREE: (800) 523-9466
Tel• (610) 282-3800; International
Fax: (610) 282-3090; International
Visit our web site at www.lutron.com
European Headquarters
Lutron EA LTD
Lutron House
6 Sovereign Close
Wapping
London, El 9HW England
FREEPHONE: (0800) 28 21 07 (U.K.)
Tel• (171) 702-0657; International
Fax: (171) 480-6899; International
LUTRON@
breaker that trips, locate the
OFF. Remove and store the
is turned OFF to work on a load
wires in the appropriate terminal
panel as shown
instructions.
Possible Cause
or Defective Module
with processor: open
in programming
Support Center
(U.S.A. , Canada and the Caribbean)
1 610 282-3800
1 610 282-3090
44 171 702-0657
44 171 480-6899
Figure 3 - Remote Power Module Wiring
Line 2 Line 1
HI
Load
Load
2
Torque Terminal Blocks using
3.5 to 5 in-lbs.
DO NOT overtighten.
Testing Prior to Connection
The module's rotary address switch can be used to operate
the circuits without a processor. Always turn OFF all circuit
breakers that feed the panel before opening the panel. See
Figure 4 for the address switch function settings
Figure 4 - Address Switch Functions
Position Proper
o All outputs OFF
1-8 Address for normal operation
9,A Not Used
B Output 1 ON / Use for temporary lighting and/or wire testing
c Output 2 ON / Use for temporary lighting and/or wire testing
Output 3 ON / Use for temporary lighting and/or wire testing
D
E Output 4 ON / Use for temporary
All outputs ON / Use for temporary lighting and/or wire testing
F
Asian Headquarters
Lutron Asuka Corporation K.K.
No. 16 Kowa Bldg. 4F
1-9-20 Akasaka
Minato-ku, Tokyo
107-0052 Japan
TOLL FREE: (0120) 083 417 (Japan)
Tel: (3) 5575-8411; International
Fax: (3) 5575-8420: International
Hong Kong Sales Office
Tel: 2104-7733; International
Fax: 2104-7633; International
Singapore Sales Office
Tel: 487-2820; International
Fax: 487-2825; International
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and printed in the U.S.A. 5/05
HW-RPM-4R
Red 1
Black 1
Black (CH)
White (CN)
Red 2
Black 2
Red 3
Black 3
Red 4
Black 4
to Processor
Module Output / Purpose
lighting and/or wire testing
81-3-5575-8411
81-3-5575-8420
852-2104-7733
852-2104-7633
65-487-2820
65-487-2825
P/N 043 049 Rev D
O
o