Herunterladen Inhalt Inhalt Diese Seite drucken
Lutron HomeWorks Interactive HWI-MI-230 Installationsanleitung
Lutron HomeWorks Interactive HWI-MI-230 Installationsanleitung

Lutron HomeWorks Interactive HWI-MI-230 Installationsanleitung

Modulinterface
Vorschau ausblenden Andere Handbücher für HomeWorks Interactive HWI-MI-230:
Verfügbare Sprachen

Verfügbare Sprachen

Installation Instructions
1.
Mount HWI-MI-230 in HWI-PNL-8-CE or HWI-PNL-5-
CE. See Figure 2 for locations.
a. For Surface Mounted Enclosures - Use No. 8 nuts
and bolts with washers (provided).
b. For Recess Mounted Enclosures - Use No. 12
self-tapping screws (provided).
Danger - Locate and lock supply circuit breaker
(MCB) in the OFF position before connecting
power.
2.
Connect Module Wire Harness. Connect the 4 conduc-
tor wire harness that is shipped inside the Module Inter-
face assembly to the module harness connector on top
of the circuit board. Note: The end of the harness that
has the longest length of cable between the end and the
second connector is the correct end to attach to the
Module Interface (this end will normally be indicated by
a serial number). Feed the end of the harness through
the module harness hole on the top end of the assembly
(see Figure 1).
Figure 2 - Module Interface Location
HWI-PNL-5-CE
Preferred Power
Wiring Entry
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
L
L
Alternate Power
N
N
N
G
Wiring Entry
TM
5
Module Location
(5 total)
4
3
2
1
HWI-MI-230
Module Interface
Control Wiring
(PELV)
HWI-MI-230
HomeWorks
Interactive
®
Interface Assembly
Figure 1 - HWI-MI-230
Module Har-
Power Input Plug
Manual Override
ADDRESS
+
-
Rotary Address Switch
HWI-PNL-8-CE
Preferred Power
Wiring Entry
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
DH
1
DH
2
DH
3
DH
4
L
N
N
N
N
N
L
L
N
N
N
G
Alternate Power
Wiring Entry
This product may be covered under one or more of the following U.S. patents:
4,797,599; 4,889,999; 5,170,068; 5,237,207 and corresponding foreign patents. U.S.
and foreign patents pending. Lutron and HomeWorks are registered trademarks and
HomeWorks Interactive is a trademark of Lutron Electronics Co., Inc.
© 2000 Lutron Electronics Co., Inc.
Module
TM
ness Hole
Module Harness
Connector (RPM Link)
1
2
3
4
Processor
COM +15 MUX MUX
Communication Link
Module Location
(8 total)
8
7
6
5
4
3
2
1
HWI-MI-230
Module Interface
Control Wiring
(PELV)
Inhaltsverzeichnis
loading

Inhaltszusammenfassung für Lutron HomeWorks Interactive HWI-MI-230

  • Seite 13 Dieses Produkt ist durch eines oder mehrere der folgenden US-Patente (4,797,599; 4,889,999; 5,170,068; 5,237,207) und entsprechende ausländische Patente gesetz- lich geschützt. Weitere US- und ausländische Patente sind angemeldet. Lutron und HomeWorks sind eingetragene Warenzeichen und HomeWorks Interactive ein Warenzeichen der Lutron Electronics Co., Inc.
  • Seite 14 Anschluß des Kabelbaums an die Module – Begin- bauen will, muß dieser mindestens 50 mA bei 28 V nend mit Modul Nr. 1 den Kabelbaum an alle instal- Gleichstrom schalten können. Sollen mehrere Modulin- lierten Module anschließen. Kabelbaumanschlüsse, die terfaces geschaltet werden, muß der Schalter zur über die Zahl der angeschlossenen Module hinausge- Schaltung der Stromstärkensumme aller angeschlosse- hen, sollten über dem letzten Modul aufgerollt und...
  • Seite 15 blinken, so befindet sich das Modulinterface im tive™ Utility) gesetzt ist. Den ordnungsgemäßen manuellen Korrekturmodus. Weitere Informationen zur Anschluß des Modulinterfaces an Link 1 des richtigen manuellen Korrektur finden Sie in Schritt 8. Sollte die Prozessors überprüfen. Sicherstellen, daß der Prozes- RPM-LED nur alle 7 Sekunden einmal aufblinken, sor korrekt adressiert ist.
  • Seite 16: Technische Unterstützung

    Sie im Rahmen der Garantie Serviceleistungen in Anspruch nehmen wollen, bringen Sie Lutron Asuka Corporation K.K. das Gerät bitte zum Händler zurück, oder schicken Sie es frachtfrei an LUTRON, 7200 Suter Road, Coopersburg, PA 18036-1299, USA. Rufen Sie das Lutron Technical Support Floor, Kowa Shiba-Koen Bldg.

Inhaltsverzeichnis