Ultimaker S6 Schnellstartanleitung Seite 2

Quick start guide
Welcome to your new UltiMaker S6.
Powerful performance, perfect integration.
Powered by our UltiMaker Cheetah motion system, the S6 brings
faster dual-extrusion printing without compromising on print
quality. It's flexible, connected, and ready for your workflow.
This quick start guide is for the UltiMaker S6 variant with the glass build plate.
It will help you set up your printer for first use.
Please retain all packaging materials for warranty purposes.
Included accessories and consumables
• Print core AA+ 0.4 mm (2x)1 • Nozzle cover (3x)
• Spool holder with • Hex screwdriver 2 mm
material guide2 • Glue stick
• Glass build plate • XY calibration guide
• Power cable • Calibration card
• Ethernet cable • Oil
• USB stick • Grease
• Anti-slip feet (4x)2 • Tough PLA 750 g (2x)
Notes and safety messages
This quick start guide contains tips and warnings:
Provides helpful information to assist with completing a task, offer alternative configurations,
or clarify specific details.
Indicates a potential hazard that could cause injury or damage if the safety instructions are
not followed.
User manual
Before using this product, read the user manual to learn about all its features and safety-related
information. You can find the full UltiMaker S6 user manual, available in English and other
languages, on our website: ultim.kr/s6-manual.
UltiMaker S6 Quick start guide
1 The print cores are already
installed in the print head.
2 The spool holder and
anti-slip feet are not required
in combination with the
Material Station.
Pro Bundle accessories
The UltiMaker S6 is compatible with the Material Station and Air Manager,
enhancing your 3D printing experience.
The Air Manager improves safety and print quality with an enclosed top
and filtration that removes up to 95% of ultrafine particles.
The Material Station enables 24/7 uninterrupted printing by automatically
managing up to six spools in a humidity-controlled chamber.
Together, they form the UltiMaker S6 Pro Bundle – your professional setup,
offering streamlined workflows and fast, high-quality prints.
Location
Before installing the UltiMaker S6, select a stable and appropriate location:
• Stability and weight: The surface must be flat, level, and strong enough to support the printer:
• UltiMaker S6: ~25 kg (55 lbs)
• UltiMaker S6 Pro Bundle: ~50 kg (110 lbs)
• Environment: The printer must be positioned out of direct sunlight during operation.
• Clearances: Ensure there is sufficient space around the printer for airflow and material handling:
• UltiMaker S6: If using the spool holder, allow at least 20 cm (8 in) of space behind the printer.
• Air Manager: Ensure at least 10 cm (4 in) of clearance behind the fan for unrestricted airflow.
• Material Station: Ensure at least 10 cm (4 in) of clearance behind the dehumidifier exhaust.
Installation
The UltiMaker S6 should be lifted by at least two people during installation.
Finish unboxing the UltiMaker S6: remove all packaging materials, remove the door seals, cut the cable
tie that secures the print head, and put aside the starter kit.
Before powering on the printer, install several hardware components, depending on the configuration.
Bowden tubes
1. Remove the two clamp clips from the print head.
2. Insert the Bowden tubes into the corresponding collets.
3. Secure the tubes with the clamp clips.
4. Click the cable clips onto Bowden tube 2 (right) and divide
them equally.
Anti-slip feet
The anti-slip feet are not required in combination with the
Material Station.
Carefully tilt the printer and place the four anti-slip feet around the
bottom of the frame panels. This keeps the printer securely placed,
even when printing at high speeds.
Original instructions EN