Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Remove the plug from the socket and clean the individual components before you actually start using the hot air fryer. Clean
the grid and pan with warm water, a mild washing-up liquid and a soft sponge. Tip: these components may also be cleaned
in the dishwasher.
Clean the interior and exterior of the appliance with a damp cloth.
This fryer works with hot air. Do not fill the pan with oil or frying fat.
• Place the hot air fryer on a heat-resistant flat surface.
• Properly place the grid in the pan.
• Place the pan in the hot air fryer.
CAUTION! Properly place the pan in the hot air fryer, otherwise it will not function.
Do not fill the pan with oil or other liquids. Place nothing on top of the appliance.
Do not place anything over the air inlet openings. This will disrupt the air circulation and will have a negative
effect on the cooking result.
4
hot air frying
The hot air fryer can be used to prepare a wide range of dishes.
1. Check that the voltage corresponds with what is stated on the information plate and insert the plug in
an earthed socket. The full display lights up and the hot air fryer is in the standby position.
2. Open the lid with the open button (6) and carefully lift the pan out of the hot air fryer by its
handles.
3. Place the ingredients on the grid in the pan. Caution: never exceed the recommended
volume and never fill the pan above the maximum, because in that case the food could
make contact with the heating element. Ensure the air is able to circulate through the
ingredients freely.
4. Properly place the pan back in the hot air fryer.
Never use the pan without the grid. If the pan is not properly placed in the hot
air fryer, the appliance will not function and error message 'C4' is shown on the
display.
5. Caution: do not touch the pan and grid during and shortly after use, as they get
very hot. Only hold the pan by its handles.
6. Press the menu key
off automatically.
7. Select an automatic menu by first pressing menu key
'Crispy' key.
– The 4 dishes shown on the left side can be cooked with 'Juicy' for a juicy cooking
result,
or with 'Crispy' for a crispy result.
– The 4 dishes shown on the right side can only be cooked with 'Crispy' for a crispy
cooking result.
Then select one of the available automatic menus that are flashing. The display now shows the
accompanying cooking time and temperature.
– When 'Juicy' is selected, the text 'Add water' starts to flash as well. Now you must first fill the water
reservoir with fresh mains water. This reservoir can contain 0.1 litres of water maximum.
– Only in case of dishes that are cooked in the 'Crispy' mode, you are able to adjust the cooking time and
temperature if you want.
If you do not want to use an automatic menu, you can set a time (1 - 60 minutes) and temperature
(40 - 200 °C) for the ' J uicy' or 'Crispy' mode yourself by using the
temperature and time.
Tip: add 3 minutes to the cooking time when the hot air fryer is cold.
8. To switch on the hot air fryer, you then press the ON key
• The display alternates between the set time and set temperature.
• The display shows the remaining time. Time and temperature can be increased and decreased during frying by
pressing the
and
• Excess oil dripping from the ingredients is collected in the pan.
9. Some ingredients must be shaken halfway the cooking time. The appliance beeps 5
times and the display shows 'turn food'. After that, place the pan back in the hot air
fryer and close the lid to continue frying.
10. Once the set time has elapsed, the hot air fryer automatically switches to the
standby position. The fan does continue to run in order to allow the hot air fryer to cool down. After that, a beep will
16
•
English
to switch on the display of the hot air fryer again after it has switched
keys. (Only in case of 'Crispy' preparation and manual setting.)
and then the 'Juicy' or
and
keys. Use the
.
key to switch between
Werbung
