Kaiser Fototechnik RSP rePRO 5612 Bedienungsanleitung Seite 6

5612_Bedien_0223.qxp_5612_Bedien1122 09.03.23 09:16 Seite 6
the locking screw (31). The vertical position of the mounting
plate (7) in relation to the base plate can be checked with
the aid of the spirit level (27) on the camera carrier, and fixed
to stop accidental movement by tightening the fixing
screws (32). This is done with the 4 mm socket wrench
(20).
5. Height adjustment
The height of the camera carrier (5) is power-adjusted by
the cable remote control (2). To move upwards and down-
wards at low speed, press button ▲ (16) or ▼ (18). For
high speed also press button (17).
6. Horizontal adjustment
Turn the adjusting cranks (30) to set the camera carrier
horizontally. You can lock the position with the blocking
screws (29).
7. Maintenance and care
All the moving parts are designed to operate without reg-
ular maintenance.
If it is frequently used, grease the spindle (23) from time to
time with the grease supplied, also when becoming more
noisy. Use only the Kaiser spindle grease (no.
000561200027).
If the travelling carriage (35) shows play, it can be read -
justed. (Please only do this if necessary.) Use the following
method. Undo the two front fixing screws (34) on both side
parts of the travelling carriage with the 4 mm socket
wrench (20). Then tighten up the four adjusting screws (33)
on the front evenly with the 2 mm socket wrench (19).
Make sure you do not overtighten the adjusting screws.
Then tighten up the fix ing screws (34).
8. Changing fuse
The fuse is in the control box (10). Before changing it, pull
out the mains plug. After pulling out the fuse holder (12)
you can replace the fuse. Use only the specified fuse.
9. Specification
Height of column:
Cross-section of column:
Maximum load of camera
carrier:
Camera mounting plate:
Mounting thread
(interchangeable):
Operating voltage:
Fuse:
Weight:
Cable:
1.50 m (4 ft. 11 in.)
120 x 80 mm
(4.7 x 3.1 in.)
approx. 15 kg (33 lbs.)
130 x 130 mm
(5.1 x 5.1 in.)
3/8" and 1/4"
100 - 240 V, 50/60 Hz
T 4 A
approx. 18.7 kg (41.2 lbs.)
approx. 2.50 m (8.2 ft.)
10. Other system components
5615 rePRO Base Stand, height approx. 66 cm, (26 in.),
with base for column, without base plate
5618 75H Base Stand, height approx. 75 cm (29.5 in.),
5610 base required, without base plate
5610 Base for RSP columns
5616 rePRO Base Plate, 80 x 60 cm (31.5 x 23.6 in.)
5617 rePRO Trans-Illuminator, 5000 K, illuminated area
43 x 48 cm (16.9 x 18.9 in.), 4 x 55 W, with high
frequency operating system
5614 rePRO Wall Mount
4421 rePRO Adapter. For attaching Kaiser enlarger
heads and copy arms of the R1 system to the
RSP columns
5627 Close-Up Adapter. Moves the camera mounting
position for approx. 15 cm (6 in.) downwards. 1/4"
mounting thread
5652 RB 570 AX LED Copy Lighting Unit with thermo-
management, 2 x 272 SMD LEDs, 5600 K,
dimmable
5641 Polarizers for 5652, 2 pieces
5648 RB 100D LED Copy Lighting Unit,
2 x 504 High-CRI LEDs, 5600 K, dimmable
For more information see the Kaiser website at
www.kaiser-fototechnik.de/en/
produkte/artikel.php?nr=5612
Errors and technical modifications excepted.
All data are approximate values.
At the end of their service life, dispose of the
products in accordance with the applicable legal
regulations.