Radio Operation - Steute Rf Is M8 Nb-St Montage- Und Anschlussanleitung

RF I/O SW...-4E(-BU)(-w/o|-2,2Ah) (SMA) (LBT)
Montage- und Anschlussanleitung / Funk-Universalsender
Mounting and wiring instructions / Wireless universal transmitter
Instructions de montage et de câblage / Emetteur universel sans fil
Istruzioni di montaggio e collegamento / Trasmettitore universale wireless
Instruções de montagem e instalação / Transmissor universal sem fio
English
Penetration of radio signals:
Material
wood, gypsum, glas uncoated
brick stone, press boards
armoured concrete
metal, aluminium lamination, water
Typical ranges:
Location
in free field (SW868/915/917)
in free field (SW922)
indoors (SW868/915/917)
indoors (SW922)
Field strength meter for range test:
Transmitter Device
SW868 swView 868 MHz
SW915 swView 915 MHz
SW917/SW922

Radio operation

The transmission of a switching command from the transmitter to the
receiver takes about 80 to 100 ms, based on the sWave ® data trans-
mission. The switching signal of a transmitter must not be generated
at a shorter distance, otherwise this signal will be overlooked. The re-
ceiver must support the sWave ® protocol of the steute modules. Each
switching operation triggers a transmission from the radio unit. This
also applies if several channels are activated or deactivated simulta-
neously. The current value of the battery voltage is transmitted with
each transmission.
Battery
Variants with battery included in delivery:
Name
RF I/O SW868-4E-2,2Ah
RF I/O SW868-4E-2,2Ah RS Components
RF I/O SW868-4E-2,2Ah LBT
RF I/O SW868-4E-2,2Ah SMA LBT
RF I/O SW915-4E-2,2Ah
RF I/O SW915-4E-2,2Ah LBT
RF I/O SW868-4E-BU-2,2Ah LBT
The delivery includes a lithium battery SL-760/S 3.6 V/2.2 Ah (AA).
To replace the battery: see section »Battery replacement«.
Penetration
90...100 %
65...95 %
10...90 %
0...10 %
Wireless range
(approx.)
450 m
150 m
40 m
20 m
Article no.
1190393
1221794
on request
Article no.
1359762
1459212
1413529
1235146
1362074
1346101
1415410
4 / 24
Variants without battery included in delivery:
Name
RF I/O SW915-4E-w/o
RF I/O SW922-4E-w/o BATT LBT
RF I/O SW917-4E-w/o
To insert the battery: see section »Battery replacement«.
Spare part:
Name
Lithium battery SL-760 (3.6 V/2.2 Ah AA)
Status signal
NOTICE
- If a jumper is inserted to set the status signal, this
jumper overwrites the receiver setting.
- If the receiver's status signal setting is to be used,
the jumper must be set as shown in Fig. »Delivery
state«.
The device can regularly transmit a status signal in which the current
switching state of the transmitter is transmitted, regardless of a
change in the switching state. The user can set the status signal at dif-
ferent intervals. There are two options for this:
1. sWave ® configuration:
- See the receiver's mounting and wiring instructions.
2. Hardware jumper:
- Loosen the cover screws with a screwdriver. Remove the cover.
- After opening, a jumper becomes visible on the printed circuit board.
Now the desired time can be set. For the evaluation of the status sig-
nal, special receivers are available from steute.
- Put the cover on. Tighten the cover screws (0.45 Nm).
There must be no foreign bodies in the sealing area.
Delivery state:
receiver's status signal
Article no.
1432305
1423394
1284629
Article no.
1351045
Example position 1:
10 s status signal