Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Pouch Description
Machine Setting
80 micron (2 x 80 micron)
100 micron (2 x 100 micron)
125 micron (2 x 125 micron)
175 micron (2 x 175 micron)
250 micron (2 x 250 micron)
Setting up and switching on the laminator
1 2 3
• Set the laminator up on a stable surface (e.g. table) close to a
mains outlet.
Ensure there is sufficient space behind the unit so the laminated
item is not blocked and can easily be removed.
• Connect the laminator to the mains outlet.
• Using the switch on the reverse of the machine, turn the machine
ON and press the Standby button on the user interface. Then
select the machine setting (75/100/125/175) on the user interface
to match the thickness of your chosen pouches (see table above).
• SMART status LED will light red during warm-up. When the
product has reached the selected temperature, the LED will turn
green.
Inserting the document into the pouch
• Insert the document into the laminating pouch. Align it to the
sealed edge as much as possible and maintain even margins left
and right.
Pouches that are too large can be trimmed to size after lamination.
Laminating
5 6
• When the POWER/READY LED indicator lights green, insert the
pouch with the sealed edge first until it gets pulled in.
• To ensure straight feeding of a pouch, please use the SMART
entry guide LEDs to help with alignment.
The laminated document automatically exits at the output side.
Letting the laminated document cool down
• Remove the laminated document and leave it on a flat surface for
one minute to cool down.
• When you have no further documents to laminate, switch off the
laminator.
Clearing a jammed pouch
• Jamming can occur when laminating unsuitable materials.
CAUTION: To prevent any damages to the laminator, the pouch must
be removed before switching off the unit.
• Press and hold the manual reverse button on the top of the
machine. The pouch will be reversed back towards the user.
• Clean the rollers after any pouch jam as described in section
"Maintenance and care".
• This machine also features an Auto reverse feature. In the event
of a jam, or the pouch not exiting the machine properly, sensors
will detect an issue and automatically reverse the pouch back out
of the machine.
Leitz Office
PRO A3
75/80 micron
100 micron
125 micron
175 micron
250 micron
4
8
Instruction Manual
Troubleshooting
Problem
Pouch does not
completely seal
the item
Pouch has waves or
bubbles
Pouch is lost in the
machine
Jamming
Pouch is damaged
after lamination
'Active Standby' function
The active standby feature uses a sensor to detect if laminating
is taking place. If no activity is detected after 15 mins of the
last laminate, the machine will enter standby mode. This will be
indicated by the LEDs flashing red every 2 seconds. To operate the
machine, press the power button on the user interface.
7
Maintenance and care
m
WARNING: UNPLUG THIS PRODUCT BEFORE CLEANING
THE EXTERIOR. WIPE EXTERIOR ONLY WITH A DAMP
CLOTH AND DO NOT USE DETERGENTS OR SOLVENTS.
Regularly feed a cleaning card or sheet of paper through the
laminator to clean the rollers. Cleaning sheet order code: 72550000.
Waste Electrical and Electronic
Equipment (WEEE)
Electrical and electronic devices contain materials and
substances that can have damaging effects on human
health and the environment. This symbol indicates that
this device must not be treated as unsorted municipal waste but
must be collected separately. Dispose of the device via a collection
point for the recycling of waste electrical and electronic equipment
within the EU, UK and in other European countries that operate
separate collection systems for waste electrical and electronic
equipment. By disposing of the device in the proper manner, you
help to avoid possible hazards for the environment and public
health that could otherwise be caused by improper treatment of
waste equipment. The recycling of materials contributes to the
conservation of natural resources.
Possible cause
Solution
Check the thickness
of the pouch and
Document may be too
the document to be
thick to laminate
laminated do not
exceed the max.
throughput thickness
Check that the pouch
Incorrect pouch
thickness is correct
thickness is being used
for the machine and
setting used
Check that the pouch
Incorrect pouch
thickness is correct
thickness is being used
for the machine and
setting used
Pouch is jammed
Pouch was sealed
'open end' first
Press and hold the
Pouch was not centred
manual reverse button
on entry
on the top of the
machine. The pouch
Pouch was not straight
will be reversed back
on entry
towards the user.
Empty pouch was used
Thick document or
foreign object was
laminated
Pass cleaning sheets
Damaged rollers or
through the machine
adhesive on rollers
to test and clean the
rollers
EN
5
Werbung
