Ego Power+ BBA2100 Anleitung Seite 10

Align the arrow on the bristle brush shaft with the arrow
EN
on the coupler (Fig. I) and push the bristle brush shaft into
the coupler until you hear a clear "CLICK" sound (Fig. J).
Fig. I parts description see below:
I-1 Shaft-Release Button
I-2 Arrow on the Coupler
I-3 Wing Nut
I-4 Arrow on the Attachment Shaft
I-5 Red Line
Fig. J parts description see below:
J-1 Red Line
4. Slightly pull the shaft of the bristle brush attachment
to verify that it is securely locked into the coupler. If
not, move the bristle brush shaft back and forth in
the coupler until a clear "CLICK" sound indicates that
it is engaged.
5. Tighten the wing nut securely.
WARNING:
Be sure the wing nut on the coupler
is fully tightened before operating the equipment;
check it periodically for tightness during use to avoid
serious personal injury.
REMOVING THE ATTACHMENT FROM THE POWER
HEAD
1. Stop the motor and remove the battery pack.
2. Loosen the wing nut.
3. With the shaft-release button depressed, pull or twist
the bristle brush attachment shaft out of the coupler
to remove it from the power head.
OPERATION
WARNING:
Do not allow familiarity with this product
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
WARNING:
Always wear eye protection. along with
hearing protection. Failure to do so could result in objects being
thrown into your eyes and other possible serious injuries.
WARNING:
Do not use any attachments or
accessories not recommended by the manufacturer of
this product. The use of attachments or accessories not
recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
◾
Cleaning areas and paths, including uneven and
jointed surfaces.
10
BRISTLE BRUSH ATTACHMENT — BBA2100
◾
Cleaning the pavement/concrete/asphalt driveways,
walkways, and yards.
WARNING:
Dress properly to reduce the risk of
injury when operating this tool. Do not wear loose clothing
or jewelry. Wear eye protection. Wear heavy, long pants,
boots and gloves. Do not wear short pants or sandals or
go barefoot.
If the surface to be cleaned is dry, spray it with water to
reduce the amount of dust created.
You should work with the bristle brush forward. Hold the
bristle brush with one hand on the rear handle and the
other hand on the front-assist handle. Keep a firm grip
with both hands while operating the bristle brush.
Hold and guide the bristle brush at a shallow angle. If the
bristle brush is held at too steep an angle, it tends to push
back towards the operator.
Maintain your grip and balance on both feet (Fig. K).
Thrown materials may seriously injure the operator or
bystander. To reduce the risk of personal injury, it is
essential to take the following precautions:
◾
Always hold the bristle brush with both hands when
operating. Use a firm grip on both handles.
◾
Move the bristle brush to the work area before
starting and start the bristle brush at a lower speed.
◾
To reduce the risk of injury from loss of control,
hold and guide the bristle brush at a shallow angle.
If the bristle brush is held at too steep an angle, it
tends to push back towards the operator.
Before each use check for damaged/worn parts
Check the brush roller, guard, front-assist handle, and
drive axle and replace any parts that are cracked, warped,
bent, or damaged in any way.
Clean the bristle brush after each use
See the Maintenance section for cleaning instructions.
TO START/STOP THE TOOL
See "STARTING/STOPPING THE POWER HEAD" section in
the power head PH1400E/PH1420E/PHX1600 operator's
manual
MAINTENANCE
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts may create a hazard
or cause product damage. To ensure safety and reliability, all
repairs should be performed by a qualified service technician.
WARNING:
Battery tools do not have to be plugged into