GRAPHITE 58G006 Benutzerhandbuch Seite 8

NOTE: BEFORE USING THE APPLIANCE, PLEASE READ
THIS MANUAL CAREFULLY AND KEEP IT FOR FUTURE
REFERENCE.
SPECIFIC SAFETY PROVISIONS
SPECIAL PROVISIONS FOR THE SAFE OPERATION OF THE
DRILL/SCREWDRIVER
• Wear ear protection and safety goggles when working
with the drill/driver. Exposure to noise can cause hearing
loss. Metal filings and other flying particles can cause permanent eye
damage .
ADDITIONAL RULES
OPERATION
• Use only the recommended batteries and chargers. Batteries
and chargers must not be used for other purposes.
• Do not change the direction of rotation of the tool spindle while it
is running. Failure to do so may damage the drill/driver.
• Use a soft, dry cloth to clean the drill/driver. Strong detergents
and alcohol must never be used.
• Do not modify the appliance yourself. Have repairs to a
defective unit carried out by an authorised service centre.
PROPER BATTERY HANDLING AND OPERATION
• The battery charging process should be under the control of
the user.
• Avoid charging the battery at temperatures below 0°C.
• Only
charge the
recommended by the manufacturer. The use of a charger
designed to charge a different type of battery poses a risk of
fire.
• When the battery is not in use, keep it away from metal
objects such as paper clips, coins, keys nails, screws,
or other small metal items that can short-circuit the
b a t t e r y t e r m i n a l s . Short-circuiting the battery
terminals can cause burns or fire.
In the event of damage and/or misuse of the battery,
gases may be released. Ventilate the room, consult a
doctor in case of discomfort. The gases may damage the
respiratory tract.
• Fluid leakage from the battery may occur in extreme
conditions. Liquid leaking from the battery can cause
irritation or burns. If a leak is detected, proceed as fol l ows:
• Carefully wipe off the liquid with a piece of cloth. Avoid contact of
the liquid with the skin or eyes.
• if the liquid comes into contact with the skin, the relevant area on the
body should be washed immediately with copious amounts of clean
water, or neutralise the liquid with a mild acid such as lemon
juice or vinegar.
• if the liquid gets into the eyes, rinse them immediately with plenty
of clean water for at least 10 minutes and seek medical advice.
• Do not use a battery that is damaged or modified. Damaged
or modified batteries may act unpredictably, leading to fire,
explosion or danger of injury.
The battery must not be exposed to moisture or water.
• Always keep the battery away from a heat source. D o not
leave it in a high temperature environment for long periods
o f t i m e (in direct sunlight, near radiators or anywhere
where the temperature exceeds 50°C).
• Do not expose the battery to fire or excessive
temperatures. Exposure to fire or temperatures above 130°C
may cause an explosion.
NOTE: A temperature of 130°C can be specified as 265°F.
All charging instructions must be followed, and the battery
must not be charged at a temperature outside the range
specified in the rating table in the operating instructions.
Charging incorrectly or at temperatures outside the specified range can
damage the battery and increase the risk of fire.
BATTERY REPAIR:
58G006
FOR SAFE DRILL/DRIVER
batteries with the
• Damaged batteries must not be repaired. Repairs to the
battery are only permitted by the manufacturer or an authorised
service centre.
• The used battery should be taken to a disposal centre
for this type of hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water.
The ingress of water into the charger increases the risk of
shock. The charger may only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any
maintenance or cleaning.
• Do not use the charger placed on a flammable surface
(e.g. paper, textiles) or in the vicinity of flammable
substances. Due to the temperature increase of the
charger during the charging process, there is a danger of fire.
• Check the condition of the charger, cable and plug each
time before use. If damage is found - do not use the
charger. Do not attempt to disassemble the charger.
Refer all repairs to an authorised service workshop. Improper
installation of the charger may result in a risk of electric shock or
fire.
• Children and physically, emotionally or mentally challenged
persons, as well as other persons whose experience or
knowledge is insufficient to operate the charger with all
safety precautions, should not operate the charger without the
supervision of a responsible person. Otherwise there is a danger
that the device will be mishandled resulting in injury.
When the charger is not in use, it should be
charger
disconnected from t h e mains.
All charging instructions must be followed, and the battery
must not be charged at a temperature outside the range
specified in the rating table in the operating instructions.
Charging incorrectly or at temperatures outside the specified range
can damage the battery and increase the risk of fire.
CHARGER REPAIR
• A defective charger must not be repaired. Repairs to the
charger are only permitted by the manufacturer or an authorised
service centre.
ATTENTION: The device is designed for indoor operation.
Despite the use of an inherently safe design, the use of
safety measures and additional protective measures,
there is always a residual risk of injury during work.
Li-Ion batteries can leak, catch fire or explode if they
are heated to high temperatures or short-circuited. Do
not store them in the car during hot and sunny days.
Do not open the battery pack. Li-Ion batteries contain
electronic safety devices which, if damaged, can cause
the battery to catch f i r e or explode.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit
shown on the graphic pages of this manual.
Jaws quick-action chuck
1.
Quick-action chuck ring
2.
Torque control ring
3.
Gear shift switch
4.
Direction of rotation switch
5.
Speed control switch
6.
Handle / handle
7.
Work area lighting
8.
Battery socket
9.
Hook for hanging the drill/screwdriver
10.
* There may be differences between the drawing and the product.
Explanation of the used pictograms
8