Ryobi RJS850 Bedienungsanleitung Seite 3

Safety, performance, and dependability have been given top
priority in the design of your jigsaw.
INTENDED USE
The jigsaw is intended to be used only by adults who have
read and understood the instructions and warnings in this
manual, and can be considered responsible for their actions.
With appropriate blades fi tted, the product is designed to cut
wood, plastic, drywall, and metal up to the depth described
in the specifi cation table.
The product is designed for handheld use. The product is not
to be mounted onto a workbench unless specifi c instructions
about how to do this are given by the manufacturer of the
product.
Do not use the product for any other purpose. Use of the
product for operations diff erent from intended could result in
a hazardous situation.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
JIGSAW SAFETY WARNINGS
■
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
■
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
■
Use the dust collection device or connect a dust
extraction vacuum when operating the product.
■
Keep mains lead clear from working range of the
machine. Always lead the cable away behind you.
■
Wear a dust mask.
Additional safety instructions
■
Avoid running the product at low speeds for extended
periods of time. Running at low speeds under constant
usage may cause the product to become overheated. If
this occurs, cool the product by running it without a load
at full speed.
■
Use the correct dust collection system as per the
instructions in this manual.
■
Ambient temperature range for tool during operation is
between 0°C and 40°C.
■
Ambient temperature range for tool storage is between
0°C and 40°C.
■
The recommended ambient temperature range for the
charging system during charging is between 10°C and
38°C.
WARNING
Dust from certain paints, coatings, and materials may
cause irritation, or allergic reactions to the respiratory
system. Dust from wood such as oak, beech, MDF, and
others are carcinogenic. Materials containing asbestos
should only be worked on or processed by qualifi ed
specialist operators.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise and the operator
should pay special attention to avoid the following:
■
injury caused by vibration
– Use the lowest speed setting which achieves the
cutting, limit exposure. See Risk Reduction.
■
injury caused by dust
– Dust may enter the eyes or respiratory system.
Wear eye protection at all times. Wear appropriate
dust control mask with filters suitable for protecting
against particles from the material being cut. Do
not eat, drink, or smoke in the work area. Ensure
adequate ventilation.
■
injury caused by electric shock
– The blade may contact hidden wiring, causing parts
of the product to become live. Always hold the
product by the designated handles and take care
when blind-cutting into walls and floors where cables
may be hidden.
■
injury caused by contact with the blade
– The blades are very sharp and will become hot
during use. Wear gloves when changing blades.
Keep hands away from the cutting area at all times.
Clamp the workpiece whenever possible.
■
injury caused by noise
– Noise can damage hearing. When using power
tools for an extended period of time, wear hearing
protection.
RISK REDUCTION
It has been reported that vibrations from handheld tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
numbness and blanching of the fi ngers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the eff ects of vibration:
■
Keep your body warm in cold weather. When operating
the unit wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
3
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL