Hookswitch Selection; Range/Power Selection; Sound Mode Selection - Jabra GN9330e USB Anleitung

3. Make a call to someone who will act as a test person.
5 6
4. Use to scroll through 12-setting transmit volume menu
confirms your voice is at the appropriate volume.
5. Press OK to confirm new setting.
The transmit volume menu is the permanent default/start position for the LCD display. After
adjusting any of the other settings via the display, it will revert to the transmit volume menu
position.
Important: For USB applications, the volume settings are fixed and need no adjustment.
2.5.2 Hookswitch selection
The GN9350e enables you to answer and end calls remotely by using the GN1000 RHL, or its
built-in electronic hookswitch (EHS) modes. EHS is only possible on certain telephone sys-
tems. In order to determine which telephones have the EHS feature enabled, please refer to our
website www.jabra.com. Please also refer to your telephone´s user manual for clarification.
4 modes are available
GN RHL non-EHS; works with the GN1000 RHL
DHSG e.g. Siemens and Elmeg desk telephones
AEI e.g. with Tenovis desk telephones
MSH e.g. with Alcatel desk telephones
Note: By default, the GN9350e is set to the RHL interface, which also is
the correct setting if you manually operate your handset when answer-
ing/ending calls as described in the Guide for basic set-up and use.
To select the appropriate interface:
3 4
1. Use to locate the hookswitch selection menu
on base display.
5 6
2. Use to select one of the 4 interfaces from the menu.
3. Press OK to confirm the interface.
Note: To use the DHSG, AEI or MSH function, connect the connec-
tion cord (accessory) to your desk telephone and the AUX port of
the GN9350e.
2.5.3 Range/power selection
Your headset offers 3 range/power modes (Normal, Low and Very Low). The Normal mode
is ideal for most users. However, if you experience interference from other communication
6
devices during your calls, you may want to switch to the Low or Very Low modes. Changing to
until your test person Low or Very Low power modes will reduce the range of your headset.
Power mode
Normal
Low
Very Low (V. low)
* In typical office environment
Note: The Normal power mode is the default setting.
To change the range/power mode:
1. Use
2. Use
3. Press OK to confirm the new mode.
2.5.4 Sound mode selection
This menu is split into two sections: "Treble/Normal/Bass" and "Fixed/Switch". These two
sections are separated by a blank line. It is possible to choose one mode in each of the two
sections.
Your headset offers 3 treble/bass modes (Treble, Normal and Bass). You can change these to
suit your personal preferences or needs, and seperately determine the USB sound quality.
Sound mode
Treble
Normal
Bass
Sound mode
Fixed
Switch
Note: The Normal mode is the default setting.
Range* DECT
Up to 100 m
Up to 50 m
Up to 20 m
3 4
to locate the range/power mode menu
5 6
to select one of the 3 modes from the menu.
Effect
Accentuates high tones
Accentuates all tones evenly
Accentuates lower tones
Effect
Speech quality in headset loudspeaker as
known from traditional telephones (nar-
rowband)
Automatically switches between wideband or
narrowband sound quality. In conference call
mode, automatic switching is disabled.
7
Range* US DECT
Up to 300 ft
Up to 150 ft
Up to 60 ft
on base display.
Benefits
Ideal for users with slight high-
frequency hearing loss
Ideal for all users
Ideal for users preferring a bass-
rich sound
Benefits
Improved talk time in USB mode
Enhanced USB sound quality