Intended Use; Additional Battery Safety Warnings; Know Your Product - Ryobi Rpd18C1 Übersetzung Der Originalanleitung

ORIGINAL INSTRUCTIONS
EN
Safety, performance, and dependability have been given top
priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults
who have read and understood the instructions and
warnings in this manual, and can be considered responsible
for their actions.
The product is intended for drilling into various materials,
including wood, metal, plastics, stone, concrete and
masonry using a drill bit having a shank diameter of less
than 13 mm. The product can be used to drive and remove
screws and bolts using an appropriate bit.
The product is intended for consumer use only.
Do not use the product for any other purpose. Use of the
product for operations different from intended could result in
a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
PERCUSSION DRILL SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
■ Wear ear protectors when impact drilling. Exposure
to noise can cause hearing loss.
Hold the power tool by insulated gripping surfaces,
■
when performing an operation where the cutting
accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS
■ Never operate at higher speed than the maximum
speed rating of the drill bit. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
■ Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
■
not apply excessive pressure. Bits can bend causing
breakage or loss of control, resulting in personal injury.
ADDITIONAL SAFETY WARNINGS
■ Clamp workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
■ Dust created by operating the product can cause
respiratory injury. Wear appropriate dust control mask
with filters suitable for protecting against particles from
the material being worked on.
■ Do not switch on the product again after it has stalled.
Switching it on again, can cause a kickback with high
reaction force. Determine why the product has stalled
and rectify it, paying heed to the safety instructions. If
necessary, remove the insertion tool.
■ Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
■ Ambient temperature range for tool during operation is
between 0 °C and 40 °C.
■ Ambient temperature range for tool storage is between
0 °C and 40 °C.
■ The recommended ambient temperature range for the
charging system during charging is between 10 °C and
38 °C.

ADDITIONAL BATTERY SAFETY WARNINGS

■ To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse the tool,
battery pack, or charger in fluid or allow fluid to flow
inside them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short
circuit.
■ Ambient temperature range for battery during use is
between 0 °C and 40 °C.
■ Ambient temperature range for battery storage is
between 0 °C and 20 °C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and
labelling when transporting batteries by a third party.
Ensure that no batteries can come in contact with other
batteries or conductive materials while in transport by
protecting exposed connectors with insulating, non-
conductive caps or tape. Do not transport batteries
that are cracked or leaking. Check with the forwarding
company for further advice.

KNOW YOUR PRODUCT

See page 43.
1. Gear selector
2. Torque adjustment ring
3. Keyless chuck
4. Direction of rotation selector
5. Variable speed trigger
6. Handle, insulated gripping surface
7. LED light
8. Battery port
9. Screwdriver bit
10. Operator's manual
11. Drill bits
12. Battery pack
13. Charger
MAINTENANCE
■ The product should never be connected to a power
supply when assembling parts, making adjustments,
cleaning, performing maintenance, or when the
product is not in use. Disconnecting the product from
the power supply will prevent accidental starting that
could cause serious injury.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
3