Remaining Hazards; Technical Data; Noise Emission; Content Of Delivery - Jet 701 Handbuch

Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging the
power cord.
Remove all loose clothing and confine
long hair.
Before operating the machine, remove
tie, rings, watches, other jewellery,
and roll up sleeves above the elbows.
Wear safety shoes; never wear leisure
shoes or sandals.
Always wear the approved working
outfit.
Do not wear gloves.
Wear goggles when working
Wear ear protectors while working on
the machine.
Install the machine so that there is
sufficient space for safe operation and
work piece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be bolted
stable on firm and levelled table
surface.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Keep children and visitors a safe
distance from the work area.
Do not operate the electric tool near
inflamm able liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Before machining, remove any nails
and other foreign bodies from the
work piece.
Work only with well sharpened tools.
Machine only stock which rests
securely on the table.
Always close the chuck cover before
you start the machine.
Specifications regarding the maximum
or minimum size of the work piece
must be observed.
Do not remove chips and work piece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
Make certain the machine is properly
grounded.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist.
The rotating drill bit can cause injury.
Thrown work pieces and work piece
parts can lead to injury.
Dust and noise can be health hazards.
Be sure to wear personal protection
gear such as safety goggles and dust
mask. Use a suitable dust collection
system.
The use of incorrect mains supply or a
damaged power cord can lead to
injuries caused by electricity.
4. Machine specifications

4.1 Technical data

Spindle speed
Chisel capacity max.
Drill chuck capacity
Head stroke
Work piece height max.
Base size 350 x 410 mm
Fence size
Chisel centre to fence max
4
Overall (LxWxH)
Net weight
Mains
Output power
Input power
Reference current
Extension cord (H07RN-F): 3x1,5²mm
Installation fuse protection

4.2 Noise emission

Acoustic pressure level (EN 11202):
Idling
In operation
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
As workplace conditions vary, this
information is intended to allow the
user to make a better estimation of the
hazards and risks involved only.

4.3 Content of delivery

13mm drill chuck
Chuck key
Spindle extension
5/8" (15,87mm) chisel bushing
3/4" (19.05mm) chisel bushing
13/16" (20,64mm) chisel bushing
Micro adjustable fence with quick cam
locks
Reversible double locking work hold-
down
Guide rollers on base
Drill depth stop
Built in chisel-to-bit-spacer
Tool tray
Diamond chisel sharpening cone
Operating manual
Spare parts list.

4.4 Machine description

1450 rpm
19 mm
13 mm
140 mm
110 mm
320 x 65 mm
110 mm
350x410x900mm
41 kg
230V ~1/N/PE 50Hz
0,56 kW (0,75HP) S1
(1,35HP) S6-40%
4.5 A
10A
67,4 dB (A)
75,5 dB (A)