Werbung
Verfügbare Sprachen
Verfügbare Sprachen
– You can also start a cleaning cycle when you wish: by pressing
cleaning program, indicated by the LED
SYSTEM CLEANING PROGRAM, fig 1 to 27.
Important:
You do not have to run the cleaning program as soon as the appliance requests
it, but you must do it reasonably soon after. If cleaning is postponed, the alert
message will remain displayed as long as the operation has not been performed.
Important:
if you unplug your machine during cleaning or in the event of electrical failure,
the cleaning program will resume the current step at the time of the incident.
It will not be possible to postpone this operation: rinsing the water circuit is
mandatory. In this case a new cleaning tablet may be necessary.
Automatic descaling program (approximately 20 minutes)
Descaling your machine ensures its proper functioning and eliminates any deposit of
limescale or tartar.
Caution: If your appliance is equipped with our Claris Aqua Filter System cartridge
please remove it before the descaling procedure (see "Removing the Claris Aqua
Filter System cartridge").
To perform this cleaning you will need:
– 1 dose of KRUPS descaler
– 1 container of at least 600 ml
The cycle will link three phases:
– 1 descaling phase
– 1st rinsing phase
– 2nd rinsing phase
When do I run this program?
The appliance notifies you when it is necessary to run a descaling program.
Descaling your machine ensures it proper functioning and eliminate any deposit of limescale or
tartar This step is very important to ensure the proper functioning and longevity of your appliance.
When the machine is switched on, the "alert" LED
light up. Then, refer to section 12 – AUTOMATIC DESCALING PROGRAM, fig 1 to 30.
Important:
The machine lets you know when it is necessary to do so. However, you can start
descaling the machine at any time by pressing
The Claris Aqua Filter System cartridge
Installation:
– Remove the water tank and empty it. If necessary, remove the used filter cartridge.
– Turn the grey ring located on the upper end of the filter cartridge until it displays the
current date. The cartridge must be changed every 2 months.
– Screw the new filter cartridge into the bottom of the water tank using the accessory
supplied with the cartridge.
– Fill the water tank and put it back in place.
– Switch on the machine by pressing ON/OFF.
– Place an empty container under the coffee nozzles.
46
and selecting the
. Then see 11 – AUTOMATIC COFFEE
and the LED
on the interface will
and selecting
.
– Press and hold "CLEAN"; the indicator lights will flash.
– Then press "START/STOP"; the water will then flow from the coffee nozzles.
– The filter is primed.
Removal:
– Remove the water tank and empty it.
– Remove the filter cartridge.
– Then follow the instructions above, in "Installation", to change the used cartridge.
OTHER FUNCTIONS
Adjustments
You can customise various settings on your machine, by adjusting the parameters of the
machine.
Important:
The machine is connected, but not switched on.
Press for 3 seconds on
, you will hear a beep.
Coffee
temperature
Press
then
Low
temperature adjustment levels for your coffee drinks. The setting is
Medium
at 2 drops by default.
High
You can also choose the length of time after which your selected
Auto OFF
appliance will automatically turn off in order to optimise your
energy consumption: 15 minutes, 30 minutes and 3 hours. The
15 mins
setting is at 3 hours by default.
30 mins
3 hours
Press
then
You have the possibility of setting up an automatic rinsing which
Auto rinsing ON
guarantees the preservation of best coffee flavor and an optimal hygiene.
Inactive
Active
Press
then
You can remove the function that detects the absence of coffee
Inhibit the "no
beans. You will no longer see the corresponding alert lights. The
beans" function
setting is active by default.
Inactive
Press
then
Active
"No beans" function
This function is used to predict the lack of coffee beans in the coffee bean container. This
lack is indicated by the warning light (V), the alert
operation.
to set the coffee temperature. There are 3
to set auto OFF.
to set auto rinsing to ON.
to inhibit the "no beans" function.
and the stopping of grinding while in
47
Werbung
