Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NOTE:
1. The Pressure Gauge is just used for measuring
measurement.
2. We recommend you clean the sand bed once a month or less regularly depending on how often
the pool is used. Do not clean the sand too frequently.
Cleaning
the
Strainer
1. Switch
off the
sand
2. Close
the
connection
3. Remove the Strainer Cover by unscrewng
4. Take out the Strainer, remove any debris.
5. Put the Strainer back into position.
6. Ensure the Seal Ring is in place. Secure the Strainer Cover back.
7. Open the connection
E:
NOT
The Straine
r
strainer will reduce the pefformance of the sand filter.
Lowering
or Draining
1. Svitch
off the
sand
2. Detach
the
Hose
from
3. Svitch
on the sand filter to remove pool water.
WARNING:
DO
NOT
Winterization
and
In areas that have freezing winter temperatures,
damage. AlloWng water to freeze will damage the sand filter and void warranty.
1
Backwash
the sand filter as previously
2. Drain the pool according to the pool owner's manual.
3. Unscrewthe
drain valve cap at the bottom of the tank and release the remaining water.
4. Disconnect
the two Hoses from the pool and the sand filter.
5. Completely spill the sand out of the tank and dry all components.
6. Move away sand filter from pool area, store the sand filter in a dry indoor location out of child's
reach
Problems
Send is flowing to the pori
No
water
flow
Excessive flier pressure
Control
Valve
leaks
from the port D
Connectnrg
leak
filter
and
set the
Control
valves.
Ensure the hole in the strainer is aligned.
valves.
must beemptied and cleaned periodically.
Pool
Water
filter
and
set Control
the
connection
valve's
DRY
RUN
THE
long-term
storage
outlined in Section II and Section Ill.
TROUBLESHOOTING
Probable
Causes
- Sand
is ton small
- Move
the
control
velve
trom
filter fifidinn
without gtnp the sand filter
- The level ofthe sand is too figh
- The
Skimmer
ig brnkgn
- Stopper plugs were not removed
- The
contrna
valve
ig get tn Cloggd
- The
Etrener
is blocked
- Sand
filter
broken
- Dirty filter
- Celciffed
sand
bgd
- Insufficient backwashing
- The pressure
gauge iE broken
- Control
Valve
ig get between
- The gasket is broken
- Waghar nf the connectors nnt in place
- Washer
of the connectors
- Lnogg
Hnggg
the water pressure,
Valve
to the
Closed
it.
Valve
to the
Drain
function.
Port
A and
sand
SAND
FILTER.
pool equipment
the
backwash
to the
two
functions
broken
not used for precision
function.
Adirty o rblocked t
filter
Port
A and
attach
must be Wnterized
to protect against
Sol utions
- Recommend
C .45mm
to C .85mm
- Stop the sand filter everytime set the control valve
- Check
Ifthe
level
of the sand
is between
and "MIN"on
the colector
- Replace the skimmer
- Remove the Gtopger plugs end insert the
dehng
screeng
- Set to filter
functon
- Cean
the
strainer
- Cell
for service
- Backwash
- Inspect gend and change itngcgggary
- Backwash
until
water
runs
clear
- Repdace the pressure gauge
- Sgt tn one
function
- Repaece the gasket
- Reposition
the washer
- Repaace the wagher
- Tighten them
to Port
D.
slica
sand
the marked
hub
Werbung
