Explosionsgeschützte Kunststoff LED Leuchte Serie: KLL 2 Technische Daten EG-Baumusterprüfbescheinigung: IBExU 16 ATEX B012 Gerätekennzeichnung nach 2014/34/EU und Norm: EN 60079-0 II 3 G Ex ec IIC T4 Gc Staub II 3 D Ex tc IIIC T80 °C Dc IECEx Konformitätsbescheinigung: IECEx IBE 16.0028 Kennzeichnung nach IECEx IEC 60079-0...
Voraussetzung für Montage-, Wartungs- und Instandsetzungsarbei- Verwendung eines Druckausgleichsstutzens verhindert werden. ten an explosionsgeschützten Betriebsmitteln ist deshalb die genaue Verwendet werden darf nur ein von der EATON/COOPER CROUSE- Kenntnis der geltenden Vorschriften und Bestimmungen, HINDS freigegebener Ex-Druckausgleichsstutzen. Er wird in eine insbesondere: nicht benötigte Gehäusebohrung zur Leitungseinführung montiert.
Explosionsgeschützte Kunststoff LED Leuchte Serie: KLL 2 Normenkonformität Installation Die Leuchte entspricht den aufgeführten Normen, in der separat Der elektrische Anschluss des Betriebsmittels darf nur durch Elek- beigelegten Konformitätserklärung. trofachpersonal erfolgen (EN/IEC 60079-14). Sie wurde entsprechend dem Stand der Technik und gemäß Die für das Errichten und Betreiben von explosionsgeschützten DIN EN ISO 9001 und EN ISO/IEC 80079-34 entwickelt, gefertigt und geprüft.
Bestimmungen überprüfen! (EN/IEC 60079-19). Bevor Sie diese Ex-Leuchte in Betrieb nehmen, kontrollieren und stellen Als Ersatz und zur Reparatur dürfen nur Originalteile von EATON/ Sie sicher, dass: COOPER CROUSE-HINDSverwendet werden. die Leuchte vorschriftsmäßig und in der vorgeschriebenen Ge- Bei Einsatz in Staub-Atmosphäre muss die Leuchte vor dem Öffnen...
Explosion protected plastic LED light fittings Series: KLL 2 Technical data Type examination certificate: IBExU 16 ATEX B012 Marking acc. to 2014/34/EU and standard: EN 60079-0 II 3 G Ex ec IIC T4 Gc dust II 3 D Ex tc IIIC T80 °C Dc IECEx type examination certificate: IECEx IBE 16.0028 Category of application...
IEC/EN 60079-14 on electrical apparatus for explosive atmospheres. explosion-proof breathing gland is often quite effective. It is allowed to use a breathing gland which is released by the EATON/COOPER The safety of people and equipment in hazardous areas depends on CROUSE-HINDS only.
Explosion protected plastic LED light fittings Series: KLL 2 Conformity with standards Installation The light fitting is conform to the standards specified in the EC-Declara- For skilled electricians and trained personnel in accordance tion of conformity, enclosed separately. with national legislation, including the relevant standards and, It has been designed, manufactured and tested according to the state of where applicable, in acc.
Repairs that affect the explosion protection, may only be carried Prior to operation, check the light fitting for its proper functioning out by EATON/COOPER CROUSE-HINDS or a qualified electrician in and installation in compliance with these operating instructions and compliance with the applicable national rules (IEC/EN 60079-19).
Seite 12
Cooper Crouse-Hinds GmbH functionality. Their use in whatever form is subject to prior approval Neuer Weg-Nord 49 by Eaton. The same applies to Trademarks (especially Eaton, Moeller, 69412 Eberbach and Cutler-Hammer). The Terms and Conditions of Eaton apply, as E-Mail: Info-Ex@Eaton.com referenced on Eaton Internet pages and Eaton order confirmations.