Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ing at least the highest no-load speed of the tool
▶ Never use saw blades made of high speed steel (HSS)
▶ Do not use a saw blade which is cracked, deformed or
dull
▶ Only use saw blades with a hole diameter which fits
the tool spindle without play; never use reducors or
adaptors to fit large-hole saw blades
▶ Protect accessories from impact, shock and grease
DURING USE
▶ Do not force the tool; apply light and continuous
pressure
▶ Keep fingers, hands and arms away from the rotating
saw blade
▶ Push spindle-lock button only when tool is at a stand-
still
▶ If the saw blade becomes blocked, switch off the tool
immediately and disconnect the plug; only then remove
the wedged workpiece
▶ In case of jamming or electrical or mechanical mal-
function, immediately switch off the tool and discon-
nect the plug
▶ If the cord is damaged or cut through while working,
do not touch the cord, but immediately disconnect the
plug
▶ Never use the tool when cord is damaged; have it re-
placed by a qualified person
AFTER USE
▶ After switching off the tool, never stop the rotation
of the accessory by a lateral force applied against it
▶ Only remove cut-offs or other parts of the workpiece
from the cutting area when all moving parts have come
to a complete standstill
▶ The saw blade becomes very hot during use; do not
touch it before it has cooled down
USE
Transport/working position
For releasing the tool (working position)
press handle downward with one hand to prevent tool
arm from swinging upward unexpectedly
pull out locking pin with the other hand, rotate it 1/4 turn
in either direction and release it in that position
guide the tool arm slowly upward
For securing the tool (transport position)
▶ press safety lever while lowering the tool arm with
handle to the stop
▶ release safety lever and press handle downward with
one hand to prevent tool arm from swinging upward
unexpectedly
▶ pull out locking pin with the other hand, rotate it 1/4
▶ turn in either direction and release it in that position
▶ use transport handle for carrying the tool
Mounting tool on working surface
▶ for safe handling always mount tool on a flat and sta-
ble working surface (e.g. workbench)
▶ use 4 mounting holes for attaching the tool with suit-
able screws to the working surface
▶ you may also clamp the tool to the working surface
with commercially available screw clamps
Dust/chip extraction
▶ mount dustbag
▶ empty dustbag regularly for optimal dust pick-up per-
formance
▶ never let the vacuum cleaner hose interfere with the
lower guard or the cutting operation
Clamping the workpiece
▶ for optimum working safety always firmly clamp the
workpiece with the adjustable clamp supplied
▶ assemble clamp H as illustrated
▶ fasten assembled clamp into support hole with knob
(on either side of the tool)
▶ press the workpiece firmly against fence
▶ adapt clamp to the workpiece with knob
▶ firmly clamp the workpiece by turning down knob
▶ do not work with workpieces that are too small to
clamp (minimal workpiece dimensions: 140 x 30 mm
length x width)
▶ for maximal workpiece dimensions use table as refer-
ence
Setting mitre angles
▶ disconnect the plug
▶ loosen locking screw
▶ hold switch handle firmly and rotate tool as well as
saw table to the left or right
▶ set the desired mitre angle (from 0° to 45°) by using
indicator
▶ tighten locking screw
▶ for quick and precise setting of often used mitre an-
gles (0°, 5°, 10°, 15°, 22.5°, 30°, 35°, 40°, 45°) the saw
Mit r e s aw | 13
Werbung
