Kraissmann 2300GS255 Betriebsanleitung Seite 12

tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
▶ Maintain power tools. Check for misalignment or bin-
ding of moving parts, breakage of parts and any other
condition that may affect the power tool's operation.
If damaged, have the power tool repaired before use.
▶ Many accidents are caused by poorly maintained pow-
er. Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed.
▶ Use of the power tool for operations different from
those intended could result in a hazardous situation.
Service
▶ Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is main-
tained.
Product Description
and Specifications
This tool is intended as a stationary machine for perform-
ing lengthways and crossways straight cuts in wood or
similar materials; also possible are horizontal mitre an-
gles of 45° (left side) to 45° (right side) as well as verti-
cal bevel angles of 45° (left side) to 45° (right side).
The equipment is to be used only for its prescribed pur-
pose. Any other use is deemed to be a case of misuse. The
user / operator and not the manufacturer will be liable
for any damage or injuries of any kind caused as a result
of this. Please note that our equipment has not been de-
signed for use in commercial, trade or industrial applica-
tions. Our warranty will be voided if the machine is used
in commercial, trade or industrial businesses or for equiv-
alent purposes..
TECHNICAL DATA
Power, W ..............................................................2300
Voltage, V ................................................................230
Frequency, Hz .......................................................... 50
No load speed, min ........................................4500
-1
Blade rated diameter, mm ................................255
Protection class.........................................................II
12 | English
BEFORE USE
▶ Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools
with a rating of 230V or 240V can also be connected
to a 220V supply)
▶ Use completely unrolled and safe extension cords
with a capacity of 16 Amps (U.K. 13 Amps)
▶ Always mount the tool on a flat and stable working
surface (e.g. workbench)
▶ Wear protective glasses, hearing protection, and pro-
tective gloves
▶ Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful (con-
tact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator
or bystanders); wear a dust mask and work with a dust
extraction device when connectable
▶ Certain kinds of dust are classified as carcinogen-
ic (such as oak and beech dust) especially in conjunc-
tion with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when con-
nectable
▶ Follow the dust-related national requirements for
the materials you want to work with • Do not work
materials containing asbestos (asbestos is considered
carcinogenic)
▶ Never use the tool without the original protection
guard system
▶ Check the protective guard for proper closing before
each use
▶ Do not operate the saw if the protective guard does
not move freely and close instantly
▶ Never clamp or tie the protective guard into the open
position
▶ Always firmly clamp the workpiece (do not work with
pieces that are too small to clamp)
▶ Always support the free ends of a long workpiece
▶ Never allow another person to hold or support the
workpiece while working; use the saw table extension
▶ Never use the tool without the table insert; replace a
defective or worn table insert
▶ Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
▶ Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
ACCESSORIES
▶ Never use grinding/cutting discs with this tool
▶ Use only accessories with an allowable speed match-