AIRLUX AHIBF971IX Bedienungsanleitung Seite 22

• Wear protective gloves before
proceeding with the installa-
tion.
• Electric Connection:
Note! Verify the data label placed inside the appliance:
- If the symbol appears on the plate, it means that
no earth connection must be made on the appliance,
therefore follow the instructions concerning insulation
class II.
- If the symbol DOES NOT appear on the plate, follow
the instructions concerning insulation class I.
Insulation class II
- The appliance has been manufactured as a class II,
therefore no earth cable is necessary. The plug must be
easily accessible after the installation of the appliance.
If the appliance is equipped with power cord without
plug, a suitably dimensioned omnipolar switch with
3 mm minimum opening between contacts must be
fitted between the appliance and the electricity supply
in compliance with the load and current regulations.
- The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral.
Insulation class I
This is a class I, appliance and must therefore be
connected to an effiecient earthing system.
- The appliance must be connected to the electricity
supply as follows:
BROWN = L line
BLUE = N neutral
YELLOW/GREEN = earth.
The neutral wire must be connected to the terminal
with the N symbol while the YELLOW/GREEN, wire
must be connected to the terminal by the earth
symbol .
When connecting the appliance to the electricity
supply, make sure that the mains socket has an earth
connection. After fitting the ducted cooker hood, make
sure that the electrical plug is in a position where it
can be accessed easily. If the appliance is connected
directly to the electricity supply, an omnipolar switch
with a minimum contact opening of 3 mm must be
placed in between the two; its size must be suitable
for the load required and it must comply with current
legislation.
• If the hob is electric, gas, or induction, the minimum
distance between the same and the lower part of the
hood must be at least 65 cm. If a connection tube
composed of two parts is used, the upper part must
be placed outside the lower part. Do not connect
the cooker hood exhaust to the same conductor
used to circulate hot air or for evacuating fumes
from other appliances generated by other than an
electrical source. Before proceeding with the assembly
operations, remove the anti-grease filter(s) (Fig.15) so
that the unit is easier to handle.
- In the case of assembly of the appliance in the suction
version prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which
has the same diameter as the air exhaust outlet hole.
If a pipe with a smaller diameter is used, the efficiency
of the product may be reduced and its operation may
become noisier.
• Hood assembly:
- Remove the structure from the packaging and remove
the 2 screws A to separate the upper part from the
lower part (Fig.2).
- Position hole template on the ceiling paying atten-
tion that the arrow is positioned on the same side
as the appliance controls (Fig.3). Make 4, Ø8 holes in
the ceiling and drive in 3 screws without completely
tightening them. Pay attention not to insert the screw
into the hole marked with an X on the hole template
(the screws and expansion plugs must be suitable for
the type of wall).
- Take the upper part of the structure B (Fig.4) and insert
the 3 slots onto the 3 screws that are not completely
tightened. Rotate slightly to fit (Fig.4). Drive in the
fourth screw X and tighten the remaining 3 to allow
definitive blocking of the upper part of structure B.
- Take the lower part of the telescopic structure C and
insert it into the upper structure B (Fig.5). Adjust the
height by referring to the amounts indicated in (Fig.15)
and block it using the 8 screws G that are supplied
(Fig.6).
• Suction version: fix the air evacuation pipe H (not
supplied) onto the connection flange F (Fig.8). Fix
the flexible pipe to the prepared air evacuation hole
(Fig.12).
• Filtering version: we have two different types of Kit,
one with extractable carbon filters (Fig.16) and the
other one with re-usable carbon filters (washable)
(Fig.17).
- Fix the air evacuation pipe H (not supplied) onto the
connection flange F (Fig.8).
- If your product is fitted with a connector flange,
perform the assembly steps indicated in fig. 7 before
fixing the cooker hood to the structure. Take connector
flange F and fit it to the upper part of the cooker hood
suction assembly using the 2 screws E (Fig.7).
- Take the upper chimney piece and fix it to the struc-
ture using the screws A (Fig.9). Join the lower chimney
piece with the upper one and fix it carefully using
adhesive tape L (Fig.10A).
- Unscrew the 2 screws O, max 3 mm (Fig.10A). Insert
the suction unit inside the structure paying attention
that the previously unscrewed screws O, hook into the
slots in the lower part as indicated in (Fig.10B). Drive
in the 3 screws N (supplied) and tighten the 2 screws
O (Fig.10B).
- Remove adhesive tape L and rest the lower chimney
piece above the cooker hood (Fig.11X).
- Lower the upper chimney by performing the reverse
operation shown in figure 9.
- If the cooker hood is supplied with a lower chimney
piece that must be fixed to the hood body with screws,
remove the anti-grease filters from the hood by acting
on the relevant handles (Fig.15).
- If necessary, fix the lower duct to the hood from the
inside, using the screws P (Fig.11Y). Re-locate the filters
in their seat.
- Fix the flexible pipe to the deflector M and fix screw I
as indicated in Fig.13, the active carbon filters must be
applied to the suction unit positioned inside the hood
(Fig.16).
- 22 -