Herunterladen Diese Seite drucken

JVC SEA-33 Bedienungsanleitung Seite 16

Werbung

SPECIFICATIONS
Circuitry
Semiconductor-L
circuit
Input section
LINE
IN
TAPE
MONITOR
Output section
LINE
OUT
TAPE
REC
(during SEA-
recording)
Rated output
Max. output
Total harmonic
distortion
Intermodulation
distortion
Gain
Frequency response
S/N ratio
Control section
SEA center
frequency
SEA control range
General
Dimensions
Weight
Accessories
Note:
: Transistor-inductor
circuit
: Input impedance
47 kohms
: Input impedance
47 kohms
: Output impedance
100 ohms
: Output impedance
100 ohms
: 2V RMS (with all
S.E.A. controls posi-
tioned at ''0'')
: 7 V RMS (with all
S.E.A. controls posi-
tioned at ''0'')
> 0,005 % (20 Hz —
20 kHz, rated output)
: 0.005 % {with all
S.E.A. controls
positioned at "'0'')
: OdB with SEA switch
DEFEAT
0 dB with SEA switch
ON
~6 dB with ATTENU-
ATOR switch at -6 dB
: 10 Hz — 50 kHz
(+0, -2 dB)
: 115 dB (at rated output,
IHF A-network short-
circuited)
: 31.5 Hz, 63 Hz,
125 Hz, 250 Hz,
500 Hz, 1 kHz, 2 kHz,
4kHz,8 kHz, 16 kHz
:+12dB
: 435(W) x 61(H) x
265(D) mm
: 3.0 kg
: 2 pairs of connection
cords (1.2 m)
IHF: Initials of the Institute of High Fidelity
in the U.S.A.
Design and specifications subject to change
without notice.
—15—
TECHNISCHE DATEN
Schaltkreise
Halbleiter-L-Schaltung: Transistor-|nduktor-
Eingangsteil
LINE
IN
TAPE
MONITOR
Ausgangsteil
LINE
OUT
TAPE
REC
(wahrend SEA-
Aufnahme)
Nennausgang
Max. Ausgang
Klirrfaktor
Intermadula-
tionsverzerrungen
Verstaérkung
Frequenzgang
Stérspan-
nungsabstand
Regelungsteil
SEA-Mittenfre-
quenzen
SEA-Regelungs-
bereich
Aligemein
Abmessungen
Gewicht
Zubehor
Hinweis:
Schaltkreis
: Eingangsimpedanz
47 kOhm
: Eingangsimpedanz
47 kOhm
: Ausgangsimpedanz
100 Ohm
: Ausgangsimpedanz
100 Ohm
: 2V RMS (mit allen
S.E.A.-Reglern auf
"O" eingestelit)
: 7 V.RMS {mit allen
S.E.A. Reglern auf
"QO" eingestellt)
: 0,005 % {20 Hz —
20 kHz, Nennausgang}
: 0,005 % (mit allen
S.E.A.-Reglern auf
"O" eingestellt)
: OdB mit SEA-Schalter
auf DEFEAT
0 dB mit SEA-Schalter
auf ON
-6 dB mit AT-
TENUATOR-Schalter
auf ~6 dB
: 10 Hz — 50 kHz
(+0, ~2 dB)
: 115 dB (bei Nenn-
ausgang, IHF A-Netz-
werk kurzgeschlossen)
> 31,5 Hz, 63 Hz,
125 Hz, 250 Hz,
500 Hz, 1 KHz, 2 kHz,
4kHz,8 kHz, 16 kHz
2 £12dB
: 435(B) x 61(H) x
265(T) mm
: 3,0 kg
: 2 Paar Anschlu&kabel
(1,2 m)
IHF: Abkiirzung des Institute of High Fidelity
in den USA
Technische Anderungen vorbehalten.

Werbung

loading