Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Volume
The desired volume can be sent using the VOLUME regula-
tor (26).
Amplifying bass
Press the BASS switch (23) to turn the bass amplification on or
off.
Switch-off
he machine is switched off when the function selector switch
(27) is turned to the TAPE OFF position. The POWER (24)
control lamp goes off. Unplug the device.
NOTE:
After approx. 15 minutes without a signal, the device will
automatically switch to standby. To use the device again,
press the
/ button (10).
USB port (25)
This device has been developed in line with the latest techni-
cal advances in the USB field. The wide range of different
USB storage devices of all types which are currently on the
market, unfortunately do not allow us to guarantee full com-
patibility with all USB storage devices. For this reason, in rare
cases there may be problems in playing back files from USB
storage devices. This is not a malfunction of the device.
1. Set the function selector (27) to CD/MP3/USB/AUX.
2. Keep the STOP/USB button (11) pressed to select the
USB mode. "USB" appears on the display.
3. Connect a USB storage device directly into the port. After
a few seconds, the total number of folders and titles ap-
pears briefly.
4. Press the
/ button (10) to restart playback . The
message " MP3, USB" and the current track and folder
are shown alternately on the display.
For operation, please refer to the section "Playing CDs/
MP3".
NOTE:
Always directly connect a USB storage medium to the USB
port to prevent any malfunctions.
CAUTION:
Before removing the USB storage device, switch the func-
tion selector (27) to TAPE OFF.
AUX IN jack
1. Connect the 3.5 mm stereo RCA cable to an external
audio source. If required, use a suitable adapter (not
included).
2. Set the function selector switch (27) to the "CD/MP3/
USB/AUX" position.
3. Insert the other end of the cable into the AUX-IN jack
(Back Side) on the unit.
4. Start the playback of your audio source. Listen to the
sound playback via the speaker.
5. For the further procedure, please refer to the user manual
of the external audio source.
NOTE:
If possible, adjust the volume of the external unit to a com-
fortable level.
Listening to the Radio
1. Set the function selector switch (27) to the "RADIO" posi-
tion.
2. Select the desired frequency band with the band selector
switch (3).
VHF (Stereo) = FM.ST, Medium wave = AM (Mono)
2. Tune in the desired station with the station adjustment
knob TUNING (5).
3. The FM ST. indicator lamp (19) will only be lit, when the
station is received in stereo quality. If reception is too
weak and there is noise on the station being received,
this lamp will flicker.
4. For FM mode pull out the telescopic antenna (6) and turn
it to improve reception.
5. An aerial is integrated into the device for the reception of
AM stations. The machine can be aligned to the station
by turning it. In this frequency band programs are trans-
mitted in "mono" only.
Playing CDs/MP3
This is how you play a CD
1. Turn the function selector switch (27) to the "CD/MP3/
USB/AUX".
2. Open the CD tray (2) by pressing the PUSH TO OPEN
button (7).
3. Insert an audio CD with the printed side facing upwards
on to the central cone so that the CD clicks into place
and then close the lid of the CD compartment.
4. After a few seconds the total number of songs/tracks is
shown in the display.
NOTE:
In the case of CDs in MP3 format the number of folders
is briefly displayed at first.
5. Press the
/ button (10) to restart playback. The CD
will play from the first title. The current track and the "CD
" or "MP3 " message are shown on the display.
NOTE:
With CDs in MP3 format the current track and folder
are shown alternately in the display.
6. In order to remove a CD, please press the STOP/USB
button (11), open the CD compartment and lift the CD
out carefully.
English
37
Werbung
