Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Classified
Memory
Function
wh
ae
The memory can be divided Nee)
for different users or pro-
grams of stations.~:
q
:
:
NOTE:
There. are times when. frequencies are left in the. machine's me-
mory from. the-final testing done prior.to shipment..If.this.is- the'
case with your TX-902/900, cancel unnecessary preset stations
according to "How to cancel memorized stations" and memorize
desired frequencies. |
@ How to classify stations
With this. model, six classes (CLASS A to F) are available and
stations can be memorized in:any class.
A total of 30 stations
can be memorized in' classes from A to F. Although the same
station can be. memorized in. different classes, the memory
number for the station will differ depending on the order in which
the station is memorized in the classes.
"MEMORY
CLASSIFIED MEMORY PRESET
- DIRECT TUNING
Number
Buttons
CD Tune in the desired station (see section on "Tuner Reception" ).
(2) Press the MEMORY button.
3
@
The MEMORY
indicator will flash for 8 seconds.
®
Press the desired Classified Memory button (one of buttons A
to F).
®
The station is memorized in the selected class with the me-
mory number which is the smallest of the unoccupied
numbers in the class.
By repeating the operations above, up to 30 stations can be me-
morized.
If an attempt is made to memorize 31 stations or more,
_"FULL" will be displayed in the Input Selector/Frequency Display,
indicating that no more stations can be memorized.
@
How to cancel
memorized
stations
Retrieve the class number you want to cancel (see "How to
retrieve memorized stations") and then press the MUTE/MODE
button while holding down the MEMORY
button.
Another
station can be memorized with the memory number which has
been cancelled.
j-O
How to retrieve memorized
stations
= «2s?
#
(Press the. Classified: Memory:button for.the desired class! it
remote-control is used, the class.next.to- the present one is re-
trieved when the CLASS button is pressed. (TX-902 only)
@ The memory number (station) which was being received
before the class is retrieved will be received.
@) There are several methods to proceed after the above operations
are carried out. Use any of the following methods.
a.
Pressing the same Classified Memory button again permits
the next preset memory number (station) to be received.
b. Input the memory number you wish to receive: 'by using the
Number buttons.
©
@
|f the memory number consists of 2 digits, input two
numbers, immediately one after the other. For. instance,
when inputting "15", "15" will not be registered if you
wait more than one second before inputting "5", resulting
in only "1" being registered.
© «tf anumber other than a number from'1'to'30, or
anumber
which:has not been: memorized is input; the number
flashes for:2 seconds and then 'the number which was
displayed before will be displayed:
@.
lf. a.number between 1 and:3
is: pressed; the display and
station. are:changed 1 second later.
c. When the
< . PRESET»
®
button ofthe remote controller
is pressed; the memory-number:- of the:class-currently being
received will be incremented or decremented. Keeping
pressing the button increments or decrements continuously.
After the maximum or minimum number is reached, the:next
class or one before the present See will he entered.
(TX-902 only)
a n e
t s
Tape Recording
:
;
'O) Make. all connections between the tape deck and the unit as
shown in the System Connections Diagram.
®
Radio:
Press the FM or AM Input Selector button.
"Record:
Press the:PHONO
Input Selector button...
CD:
Press the CD Input Selector button:
°°"
8: Put the tape deck in the recording mode. The recording can be
monitored through the speakers or headphones as desired. For
TAPE-2, turn on the corresponding Tape Monitor button to hear
the signal that, having been recorded, is returned from the deck
to the TX-902/900.
(if. the deck has three heads)...
@® Set the proper recording level using the controls on the tape
deck used for: recording. Also, during recording and dubbing
operations, never change the positions of any Sones (bass,
treble, etc.) on this unit.
Tape-to-Tape
Dubbing
oO) Connect the two tape decks to this-Unit as'shown in the System
Connections diagram.
;
@) Load the original tape.in. tape deck 1. and'the blank tape in tape
deck 2.
;
® Press the TAPE-1 fiput 'Selector button.
@
Put tape deck 1 in the playback mode and tape deck 2 in the
recording mode.
®
The source signal can be monitored through the speakers or
headphones, when the TAPE-2 MONITOR button is in the OFF
position: If tape deck 2 has three heads, the just-recorded signal
can be monitored (when the TAPE-2 MONITOR buitton is in
the ON position): "Refer to the tape deck instruction Ensriuels
for more details.
~*~"
Using:the Graphic Equalizer
:
@ Connect the graphic equalizer to the TAPE- . 2 jacks 0
on one rear
panel.
@
if.a second.tape deck. is-used, connect. it:to ve eee jacks on
"the graphic equalizer.
®
Press the TAPE-2 MONITOR
button:
ris
@
Follow the graphic equalizer operating instructions.
® To record an:equalized signal, use tape Geek 2 eouhecied to
"the equalizer)-for recording.
a
Werbung
