Kärcher HD 6/15-4 M Classic Bedienungsanleitung Seite 11

Screw connection part
18
Nozzle
19
Spray lance
20
Trigger gun
21
Safety lock
22
Trigger
23
High pressure hose
24
Initial startup
Initial startup
DANGER
Danger of injury from electric shock
Only allow authorised technical specialists to install the
water supply, electrical connections and high-pressure
network.
Unpacking
1. Check the contents of the package when unpacking.
2. Notify the dealer immediately in the case of shipping
damage.
Colour coding
Control elements for the cleaning process are yel-
low.
Installing push handle
1. Insert the push handle into the machine.
2. Fix the push handle by the fasteners.
Illustration B
Installing accessories
1. Fix the nozzle onto spray lance with screw connec-
tion part.
2. Connect the spray lance to the trigger gun.
3. Connect high pressure hose to water outlet and trig-
ger gun.
Illustration C
4. Connect the adapter to the water inlet.
Water connection
Connection to a water line
WARNING
Health risk from return flow of contaminated water
into the drinking water network.
Observe the regulations of your water supply company.
According to applicable regulations, the device must
never be used with the drinking water network without a
system separator. Use a system separator from
KÄRCHER or a system separator as per EN 12729
Type BA. Water that has flowed through a system sep-
arator is classified as undrinkable. Always connect the
system separator to the water supply and never directly
to the water connection on the device.
1. Check the feed pressure, input temperature and in-
put amount of the water supply. See the "Technical
data" section for the requirements.
2. Connect the system separator and water connection
of the device with a hose (minimum length 7.5 m,
minimum diameter 1").
The supply hose is not included in the scope of de-
livery.
3. Open the water inlet.
Suck water from the container
1. Screw the suction hose (order number 4.440-207.0)
and filter (order number 4.730-012.0) onto the water
connection.
2. Vent the device.
Vent the device
1. Unscrew the nozzle from the spray lance.
2. Allow the device to run until the escaping water is
free of air bubbles.
3. In the case of venting problems, allow the device to
run for 10 seconds and then switch it off. Repeat the
procedure several times.
4. Switch off the device.
5. Screw the nozzle back in place.
Electrical connection
DANGER
Risk of injury from electric shock
Use a plug to connect the device to the mains grid. Per-
manent connection to the mains grid is prohibited. The
plug is used for disconnection from the mains.
See the type plate or technical data for the connection
values.
1. Unwind the mains cable and place it on the ground.
2. Plug the mains plug into the socket.
Operation
DANGER
Risk of injury from the high-pressure water jet
Never fasten the trigger in the actuated position.
Do not use the high-pressure gun when the safety lock
is damaged.
Push the safety latch of the high-pressure gun forwards
every time before starting work with the device.
High-pressure operation
Note
The device is equipped with a pressure switch. The
motor only starts up when the high-pressure gun is
open.
The high-pressure hose should be kept away from
sharp edges.
The Servo Control is forbidden in the machine, as it
can lead to higher wear of the overflow and cause
damages.
1. Open the water supply.
2. Set the power switch to "I".
3. Open the safety lock of the high-pressure gun.
4. Aim the high-pressure gun at the object to be
cleaned.
5. Open the high-pressure gun and start the cleaning
operation.
Operation with detergent
Note
A foam lance (optional) is needed for operating with de-
tergent.
WARNING
Incorrect handling of detergents
Health risk
Adhere to the safety instructions stated on the detergent
packaging.
ATTENTION
Unsuitable detergents
Damage to the device and the objects to be cleaned
Use only detergents approved by KÄRCHER.