Milwaukee AGV 12-125 X Originalbetriebsanleitung Seite 16

TECHNICAL DATA
Angle Grinder
Production code
Rated input
Rated speed
D= Grinding disc diameter max.
d= Grinding disc hole diameter
b= Cutting disc thickness min. / max.
b= Grinding disc thickness max.
D= Grinding surface diameter max.
D= Wiring brush diameter max.
D
Thread of work spindle
GB
Weight according EPTA-Procedure 01/2014
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Surface grinding: Vibration emission value a
Uncertainty K=
Disc sanding: Vibration emission value a
Uncertainty K=
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60745 and may be used to compare one tool with another..It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when
it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grin-
der, sander, wire brush or cut-off tool. Read all safety
warnings, instructions, illustrations and specifications
provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
English
14 14
h,SG
h,DS
b) Operations such as polishing are not recommended
to be performed with this power tool.Operations for which
the power tool was not designed may create a hazard and cause
personal injury.
c) Do not use accessories which are not specifically desi-
gned and recommended by the tool manufacturer. Just
because the accessory can be attached to your power tool, it does
not assure safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accesso-
ries running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately guarded
or controlled.
AGV 12-125 X AGV 12-125 X PD
(220-240 V) (220-240 V)
4586 18 04... 4584 76 04...
... 000001-999999 ... 000001-999999
1200 W 1200 W
11000 min 11000 min
-1 -1
125 mm 125 mm
22,2 mm 22,2 mm
1 / 3 mm 1 / 3 mm
6 mm 6 mm
125 mm 125 mm
75 mm 75 mm
M 14 M 14
2,4 kg 2,4 kg
89,0 dB(A) 89,0 dB(A)
100,0 dB(A) 100,0 dB(A)
7,8 m/s 7,8 m/s
2 2
1,5 m/s 1,5 m/s
2 2
3,6 m/s 3,6 m/s
2 2
1,5 m/s 1,5 m/s
2 2