Werbung
Keep the instructions for future.
NF-EN-14619
READ THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER
BEFORE USING. MAXIMUM WEIGHT: 100 KG
Warnings
- The scooter is suitable for 5 years old or above. It is not a toy, but
sports equipment for physical training, it is not intended for use in
extreme sports such as jumping, ollie ramps, etc. This product should
never be used at a skate park for an "aggressive" use (challenging
skateboarding moves, etc.).
- Use with caution on a flat, clean, dry surface and, if possible, away
from other users, and obey the road safety rules.
- Check local laws regarding scooter use, respect all the traffic rules
and signs. Stay away from other pedestrians or users on public roads.
- Best when used on a flat, dry surface free of gravel and grease. Avoid
bumps and drainage grates that might cause an accident.
- Warning! Protective equipment consisting of wrist protectors, gloves,
knee pads, helmets and elbow pads should be worn.
- Warning! T-bar folding and unfolding shall be done by an adult. The
scooter can only be used by children once the adjustment is done.
- Do not allow more than one child to ride the scooter at the same time.
- Do not use on wet days, or on wet ground.
Using the scooter
• Before and after each use: To prevent pinched fingers, carefully
follow the instructions of unfolding and folding. Make sure that the
locking mechanisms are securely locked:
- Check the height of the steering system and make sure that the nuts
are tightened and the handlebars and front wheel are perpendicular.
- Check all of the connection elements: the brake, the quick release
system of the steering column and the wheel axles must be correctly
adjusted and must not be damaged.
- Also check the wheels' wear.
6
• Braking:
- A brake is located at the rear, when necessary, press down on it to
slow down. Press down gradually to prevent skidding or loss of stabi-
lity. The metal brake may heat up after multiple uses. Avoid touching it
during and after use.
Adjustable steering angle control system: (See page 3)
An adjustable knob located at the top of the scooter deck allows you to
control the turning radius of the front wheels. Turn the knob clockwise
for the turning angle to decrease. Turn the knob anti-clockwise for the
turning angle to increase.
Assembling the product (See page 2-3)
Insert the handle bar (T-bar) tube into the hole at the front of the main
board between the two front wheels while paying attention to the
direction of insertion.
Ensure the spring loaded button pops out and locks the bar in place
properly.
ULTIMUM is provided with an adjustable T-bar which can be adapted
to the user's height (6 positions). The spring loaded button shall be in
the hole when adjusting the T-bar height.
Make sure that for the lowest position of T-bar, the button is locked
into the lowest hole. Loosen the quick release clamp of the T-bar
when adjusting. Tighten the quick release clamp to secure T-bar after
adjustment.
FOLD & UNFOLD THE SCOOTER SAFELY (See page 2)
Fold up the scooter from standing mode:
Press the button on the bottom of the T-bar and pull it up until it is
free to turn. Turn the T-bar until it comes to lie horizontally. Lock it in
position by pushing it into the hole until it "clicks" in. It is now in trolley
mode and you can carry it around.
Unfold the scooter from trolley mode:
Press the button on the bottom of the T-bar and pull it up until it is
free to turn. Turn it carefully until the T-bar is vertically standing on the
deck. Push in the T-bar until you hear a "click" sound and make sure
the T-bar is securely locked before playing.
Disassemble the T-bar from the deck:
Press the button on the bottom of the T-bar and pull it up until it is free
to turn. Turn the T-bar and watch the Globber ring around the hole.
Align the 2 pins on the T-bar with the slots of the Globber ring, so that
it can then be pulled out easily.
Warning! Be careful when you do any installation and transformation
work. While turning the T-bar, make sure no other people are in the
close vicinity around the scooter since the T-bar turns requires a
big turning angle. Keep the kids in a safe distance while installing &
transforming the scooter to avoid accidental injuries.
Warning! Risk of injury by pinching!
Do not insert your fingers into the shaded area
indicated.
During use:
- Standing on the scooter, with one hand on each handle, push with
one of your feet to move forward. Proceed with caution at the start.
- Shoes are mandatory and we strongly recommend wearing pants and
long sleeve shirts to avoid injury if you fall.
- The scooter does not include any headlights or lights. It is therefore
not suitable for use at night or during periods when visibility is limited.
DO NOT FORGET TO REGULARLY TIGHTEN ALL BOLTS AND
SCREWS TO AVOID MISALIGNMENT OR LOSS OF THE SCREW.
Care / Maintenance: regular maintenance is a safety commitment;
- Wheel bearings: avoid going through water, oil or sand as this can
damage wheel bearings. To look after the wheel bearings, syste-
matically check that the wheels turn properly by turning the scooter
upside-down and using your hand to spin the wheels. If the wheels do
not spin they must be removed to check their condition. First unscrew
the wheel axle, remove the axle and detach the wheel, then carefully
push the two wheel bearings out of their housing. If they are chipped
or dented, new ones should be bought. If there is no visible damage,
they must then be oiled. To do this, remove all traces of grease, mud
or dust with a kitchen towel or cloth, and re-oil them with a grease
spray or by leaving them to soak overnight in oil [turn them several
times in the oil first]. Then reassemble the wheel bearings and axles,
followed by the wheel, onto the scooter. Proceed in the same manner
for the other wheel.
- Wheels: the wheels wear down with time and can be pierced if
overly used on rough surfaces. The back wheel on which the brake
is applied is particularly affected after several hours of braking. In the
interests of safety, they should be checked regularly and changed if
necessary.
- Modifications: the original product must by no means be modified
except for the maintenance-related changes mentioned in these
instructions.
- Nuts, axles and other self-locking fixings: these should also be
checked regularly. They can become loose after a while in which case
they should be tightened. They can become worn and not tighten
properly, in which case they should be replaced.
7
Werbung
