Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BTL5-P/I1-M_ _ _ _-H/W-S32/K_ _/KA_ _
Micropulse Linear Transducer - Rod Style
7
Technical Data
Typical values at DC 24 V and 25 °C. Ready for operation at once, full accuracy after warm-up. With magnet
BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Resolution
Hysteresis
Repeatability
(resolution + hysteresis)
System resolution is determined by
the processor or external controller.
Recommended sampling rate:
Nominal length
f
Standard
< 1000 mm
0.5 to 2 kHz
< 2000 mm
0.5 to 1 kHz
> 2000 mm
0.5 kHz
Non-linearity:
Nom. length < 500 mm > 500 mm
±100 µm ±0.02 % FS
Temperature coefficient
(6 µm + 5 ppm * nominal length)/K
Shock loading
100 g/6 ms
per IEC 60068-2-27
1
Continuous shock 100 g/2 ms
per IEC 60068-2-29
1
Vibration
12 g, 10 bis 2000 Hz
per IEC 60068-2-6
1
(take care to avoid inherent reso-
nances of protective tube)
Pressure
up to 600 bar
when installed in a
hydraulic cylinder
1
Individual specifications as per
Balluff factory standard
7.1
Dimensions, weights,
ambient conditions
Nominal length
< 4000 mm
➥ ➥ ➥ ➥ ➥ Fig. 3-2
Dimensions
Weight
ca. 2 kg/m
Housing
Stainless steel
Pressure tube Stainless steel 1.4571
diameter
10.2 mm
wall thickness
2 mm
e-modulus
ca. 200 kN/mm
Mounting threads M18×1.5
Operating temp.
–40 °C to +85 °C
Humidity
< 90 %, non-dewing
Protection rating per IEC 60529
with connector attached:
connector version IP 67
cable version
IP 68
(type tested at 5 bar / 48 h)
7.2
Supply voltage (external)
8
english
< 2 µm
Regulated supply voltage
< 4 µm
BTL5-_1...
< 6 µm
Ripple
Current draw
Inrush
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing
7.3
Control signals
INIT pulse
Level
Length
7.4
Connection to processor/
controller
BTL5-...H/W-S32
with connector,
axial arrangement, for shielded
cable, max. length 500 m,
Diameter 6 to 8 mm
BTL5-...H/W-K05
with connecting cable
radial arrangement, 5 m long
BTL5-...H/W-KA05
with connecting cable
axial arrangement, 5 m long
7.5
Included in shipment
Transducer
2
DC 20 to 28 V
< 0.5 V
pp
< 90 mA (at 1 kHz)
< 3 A/0.5 ms
500 V
+5 V RS 485/422 driver
1 µs (max. 3 µs)
➥ ➥ ➥ ➥ ➥ Fig. 3-2
7.6
Magnets
(order separately)
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
➥ ➥ ➥ ➥ ➥ Fig. 3-4
Dimensions
Weight
approx. 10 g
Housing
anodized aluminum
Operating temp.
–40 °C to +85 °C
Included:
8 mm spacer
Material
POM (polyoxymethylene)
Magnets BTL5-P-4500-1
(Electromagnet)
Weight
approx. 90 g
Housing
plastic
Operating temp.
–40 °C to +60 °C
7.7
Mounting nuts
(order separately)
Mounting nuts M18*1,5
BTL-A-FK01-E-M18X1,5
Mounting nuts 3/4"-16UNF
BTL-A-FK01-E-3/4"-16UNF
7.8
Accessories (optional)
➥ ➥ ➥ ➥ ➥ Fig. 4-1
Connectors
Werbung
