Bosch GCM Professional 8000 SJ Originalbetriebsanleitung Seite 29

– Turn the saw table (22) to the 0° detent (28). The lever
(26) must be felt to engage in the detent.
– Loosen the clamping handle (10) and use the handle
(16) to swivel the tool arm all the way to the left (45°).
Checking (see figure O1)
– Set an angle gauge to 45° and place it on the saw table
(22).
The leg of the angle gauge must be flush with the saw blade
(39) along its entire length.
Setting (see figure O2)
– Loosen the clamping handle (10).
– Loosen the lock nut of the stop screw (9) using a com-
mercially available box-ended or open-ended spanner
(size 10 mm).
– Turn the stop screw as far in or out as needed until the leg
of the angle gauge is flush with the saw blade along its en-
tire length.
– Retighten the clamping handle (10).
– Then retighten the stop screw lock nut (9).
If the angle indicator (32) is not aligned with the 45° mark on
the scale (31) following adjustment, first check the 0° set-
ting for the bevel angle and the angle indicators once more.
Then repeat the adjustment of the 45° bevel angle.
Aligning the mitre angle indicator (see figure P)
– Bring the power tool into the work position.
– Turn the saw table (22) to the 0° detent (28). The lever
(26) must be felt to engage in the detent.
Checking
The angle indicator(24) must be in line with the 0° mark of
the scale (5).
Setting
– Loosen the screw (45) using a cross-headed screwdriver
and align the angle indicator along the 0° mark.
– Retighten the screw.
Transport (see figure Q)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw (11) if it is tightened. Pull the
tool arm fully forwards and retighten the locking screw.
– Bring the power tool into the transport position.
– Remove all accessories that cannot be securely fitted to
the power tool.
If possible, transport unused saw blades in an enclosed
container.
– To lift or transport the power tool, hold it by the recessed
handles (4) on either side of the saw table (22).
Only use the transport devices to transport the power
u
tool and never the protective devices.
Bosch Power Tools
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller (20) regularly.
Noise reduction measures
Measures implemented by the manufacturer:
– Soft start
– Provided with a saw blade specially developed for noise
reduction
Measures implemented by the operator:
– Low-vibration mounting on a stable work surface
– Use of saw blades with noise-reducing functions
– Regular cleaning of the saw blade and power tool
Accessories
Screw clamp
Insert plates
Dust bag
Saw blades for wood and fibreboard, panels and strips
216 x 30 mm saw blade, 48 teeth
Saw blades for plastic and non-ferrous metals
216 x 30 mm saw blade, 80 teeth
Saw blades for all types of laminate flooring
216 x 30 mm saw blade, 60 teeth
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
English | 29
Article number
1 609 B04 224
1 609 B05 242
1 609 B05 010
2 608 640 641
2 608 640 447
2 608 642 133
1 609 92A 7NC | (26.04.2022)