Panasonic MJ-L500 Bedienungsanleitung Seite 11

Troubleshooting
Problem
●
Is the mains plug inserted into a household mains socket?
➡
Insert the mains plug into a household mains socket.
●
Set the juicer correctly.
➡
The hopper needs to be turned until you hear a "click" sound.
If you fail to do so, the juicer will not run after the power is
The juicer does not
switched on. (P. GB14)
run after the power is
●
The circuit breaker protection is activated.
switched on.
 •Youhaveusedprohibitedingredients.
 •Thevolumeofingredientsistoolarge.
 •Theingredientsaretoohard.
➡
See "circuit breaker protection" (P. GB21).
Remove prohibited ingredients from the juicer.
●
The operating time is longer than the rated duration.
➡
Follow the rated duration (within 15 minutes).
The motor housing is hot. To resume operation, please wait for at least 30 minutes. This
allows the motor housing cool down and avoid failure due to
overheating of motor.
●
The hopper is open.
➡
Switch off the power, close the lid, and start again.
●
The circuit breaker protection is activated.
•Youhaveusedprohibitedingredients.
•Thevolumeofingredientsistoolarge.
The juicer stopped
•Theingredientsaretoohard.
suddenly.
➡
See "Circuit breaker protection" (P. GB21).
Remove prohibited ingredients from the juicer.
●
Clogging of pulp spout.
➡
Switch off the power and remove residue using the tip of
brush handle.
●
This is normal.
You may hear sound such as squeaky or cracking.
Noise during operation.  •These are the sound of ingredients being compressed.
(Depending on the ingredients, the noise may be quite loud.)
 •This is the sound of rotating brush contacting with filter.
●
Packing the gasket, rubber brushes and/or rubber plug are not
Leakage of juice or
assembled correctly.
frozen dish.
➡
Assemble them correctly. (P. GB12, 13, 19)
●
This is normal.
The bowl or motor
Since the juicing bowl and motor housing are a split type, they
housing shakes during may shake when the squeezing screw is rotating.
Do not press the lid or juicing bowl. (Doing so may result in
operation.
failure of the juicer.)
●
Abnormal noise or The juicing screw and attachments are not assembled correctly.
➡
vibration. Assemble the juicing screw and attachments correctly (P. GB12-13).
GB20
Please check the following before contacting
us for repair.
Cause and solution
Circuit breaker protection
The motor may stop running when the circuit breaker protection is activated to prevent overload of motor.
Ifthemotorstops,pleasetakethefollowingsteps:
1
Switch off the power.
2
Press the "REVERSE" button to allow reverse operation for
several seconds.
●
If the squeezing screw fails to run after reverse operation, then it means overheat protection
is activated. In this case, please unplug the mains plug and leave the juicer cool down for at
least 30 minutes.
3
Switch off the power and remove ingredients from attachments.
4
Press the "ON" button.
●
Reduce the amount of ingredients being fed in and push them gently into feeding tube.
Replacement Parts
■ ■
Filter Gasket
Part number: XXXX Part number: XXXX
■ ■
Pulp container Rotating brush
Part number: XXXX Part number: XXXX
■
Juice container
Part number: XXXX
Specifications
Power supply
Power consumption
Operation rating 2consecutivecyclesof15min.ON,then5min.OFF
Dimensions (W ∙ D ∙ H) (approx.)
Mass (approx.)
Lenght of the mains lead (approx.)
ON
I
O
•
R
OFF
REVERSE
■
Frost attachment
Part number: XXXX
■
Rubber brush
Part number: XXXX
MJ-L500
220 - 240 V ~ 50 - 60 Hz
150 W
●● × ●● × ●● cm
● . ● kg
1.0 m
GB21