Werbung
Verfügbare Sprachen
Verfügbare Sprachen
(5) Mute Enable – Selection of MUTE ENABLE allows dynamic function buttons to operate as Mute controls for the module inputs and power output channels.
The MUTE ENABLE button ashes when the mode is selected; a subsequent press deselects the mode. If left activated, MUTE ENABLE mode will automatically
disable two minutes after last mute action.
(6) Meter – Successive presses of the METER button scroll through meter views: Amp, Temperature, Input and Module meters, returning to Home. Pressing METER
from Menu Mode returns display to Meter Mode Home view.
(7) Menu – Pressing the MENU button changes the display to the top level menu, with dynamic function buttons enabling access to various information displays
and function settings.
(8) Dynamic Function Buttons with LEDs (Left of LCD) – The function of these buttons change according to the currently selected view or menu.
• In Menu Mode they are used for menu navigation and for parameter selection
• In Meter mode they provide Mute/Unmute function for the four inputs in conjunction with MUTE ENABLE.
• Internal mute point(s) depend on selected meter view. The four LEDs display mute status (red= mute, green = unmute) as well as fault and warning indications.
Global faults and warnings are indicated by simultaneous illumination of all four LEDs. Please refer to full Operation Manual for more information.
(9) Dynamic Function Buttons with LEDs (Right of LCD) – The function of these buttons change according to the currently selected view or menu.
• In Menu Mode they are used for menu navigation and for parameter selection
• In Meter mode they provide Mute/Unmute function in conjunction with MUTE ENABLE. Internal mute point(s) depend on selected meter view. Please refer to
full Operation Manual for more information.
All LEDs provide mute, clip, fault and warning indication for the power output channels.
Communication LED – Steady white illumination indicates Module/Frame is selected in Lake Controller; ashing indicates communication with Lake
(10)
Controller. Brightness is adjustable in the Frame page of Main menu.
Rotary Encoder – Turning the encoder modi es various parameters in the menu. The ring around the encoder illuminates whenever a menu item is selected
(11)
that permits adjustment of values. In Home view, the encoder is used to scroll through Meter views.
Exit – Pressing EXIT returns the menu up one level when navigating in Menu mode. In Meter mode, EXIT returns display to Home view.
(12)
Rear panel
(3)
SPEAKER OUTPUTS
CH 1
CH 2
Ser. N:o
Removed!
SPEAKER OUTPUTS
1+/- CH 1+/-
CLASS 3
2+/- CH 2+/-
1+:+
1+/- CH 1+/-
3+/- CH 3+/-
WIRING
BRIDGE CH 1 & 2:
2- : -
2+/- CH 2+/-
4+/- CH 4+/-
Ser. N:o
Removed!
INPUT 1
INPUT 2
INPUT 3
ANALOG WITH ISO FLOAT
TM
(1)
(1)
INPUT 1
INPUT 2
INPUT 3
CH 3
CH 4
ANALOG WITH
I
SO-
F
LOAT
TM
CLASS 3 WIRING
(4)
1+/- CH 3+/-
2+/- CH 4+/-
BRIDGE CH 3 & 4: 1+ : +, 2- : -
1Gbps
PRIM
ACT
1Gbps
INPUT 4
INPUT 1-2
INPUT 3-4
LINK
PIN 1: SCRN
2: POS 3: NEG
AES/EBU
SWITCHED 00/ 000 Base-TX
1
1
(2)
(5)
(2)
(1)
(5)
1Gbps
PRIM
ACT
1Gbps
INPUT 4
INPUT 1-2
INPUT 3-4
LINK
PIN 1: SCRN 2: POS 3: NEG
AES/EBU
SWITCHED 00/ 000 Base-TX
1
1
(3)
CH 1
CH 2
SPEAKER OUTPUTS
CH 3
SEC
ACT
CH 1
CH 2
LINK
CLASS 2
WIRING
1+/- CH 1+/-
1+/- CH 3+/-
1+/- CH 2+/-
2+/- CH 2+/-
2+/- CH 4+/-
(6)
(4)
Quick Start Guide
(6)
(6)
SEC
ACT
100-240V
2400-2950W
50-60Hz
LINK
Made in Thailand
Must be grounded/earthed
Must be
grounded/
earthed
100-240V
2400-2950W
50-60Hz
CH 4
CH 3
CH 4
1+/- CH 4+/-
(7)
17
Werbung
