Werbung
Verfügbare Sprachen
Verfügbare Sprachen
wire Ref. 1072/57 (optional, not provided with the
product).
The B-BUS PC program can be used for simple
and fast module programming. The B-BUS program
can be downloaded free of charge from the Urmet
Domus web site (http://www.urmetdomus.it).
Minimum PC requirements are:
• 486 processor or higher
• Windows 95 or 98 operating system
• Use of a mouse is recommended.
The signals on the 9-pin female D-sub connector are:
Pin 1 n.c.
Pin 2 RX PC data
Pin 3 TX PC data
Pin 4 n.c.
Pin 5 Ground
Pin 6 n.c.
Pin 7 n.c.
Pin 8 n.c.
Pin 9 n.c.
Connect wire 1072/57 between module and PC
serial port to carry out the following operations:
1) Download data from PC (refer to the B-BUS
program for additional information). The following
will appear on the module.
Data reception
in course...
The module will become operative again at the end
of the operation.
2) Upload data to PC (refer to the B-BUS program
for additional information). The following will
appear on the module:
PLEASE
WAIT
The module will become operative again at the end
of the operation.
VOLUME REGULATION
Volume levels are calibrated by default so not
to required adjustments in most cases. Use a
screwdriver to adjust the trimmers if required.
26
DISPLAY CONTRAST REGULATION
The display contrast is set at the factory and will
not need to be adjusted in most installations. Use a
screwdriver to adjust the trimmers if required.
CALLS TO USERS
A user can be called by entering the user's code on
the keypad. Obviously, the code must be known to
do so. The name can be sought in the integrated
electronic directory if the code is not known.
CALLS TO USERS BY SELECTING THE NAME
The following message will appear on the display:
Select NAME
↑
↓
with
or
Press
or
to scroll the user's names and codes.
Hold either button pressed to scroll the names
faster. Select the name and press
to call the
selected user. The apartment door phone will ring
for approximately 3 seconds. Hold
pressed to
send up to three consecutive calls.
Name/code display example:
URMET DOMUS
1001
The following prompt will appear on the display if
is not pressed for longer than two seconds after
selecting a name:
To call
press
At this point, either press
to call or press
to scroll the name list.
The following will appear on the display when the
button is pressed:
CALL
IN COURSE
DS1072-026A
Press
to interrupt the call to the previously
selected user.
The following message will appear on the display if
the user lifts the handset:
TALK
PLEASE
Press
to end the conversation with the user.
The following message will appear if the user
does not answer within the programmed off-hook
stand-by time:
User
does not reply
CALLS TO USERS BY SELECTING THE CODE
Select NAME
↑
with
Dial the code of the user to be called (numeric or
alphanumeric with optional keyboard). The following
will appear on the display:
CALL TO:
n°1001
Select the code and press
user. The apartment door phone will ring for
approximately 3 seconds. Hold
up to three consecutive calls.
CALL
IN COURSE
or
Press
to interrupt the call to the previously
selected user.
The following message will appear on the display if
the user lifts the handset:
TALK
PLEASE
DS1072-026A
Press
to end the conversation with the user.
The following message will appear is the user
does not answer within the programmed off-hook
stand-by time:
does not reply
DIRECT CALL TO CONCIERGE SWITCHBOARD
Press
on a call module installed in a system
with concierge switchboard to call it directly. This
is only possible when the concierge switchboard
is in day mode, i.e. when the concierge service is
operative and the function has been activated (see
"Programming").
The following message will appear on the display:
↓
or
The following will appear on the display if the button
A is pressed and either the concierge switchboard
is in night mode or the function has not be activated
(see "Programming").
to call the selected
DOOR OPENER CODES
pressed to send
Press the
opener code. Symbol "∗" will appear on the display
when entering the code for each button. The module
will open the door if the code is valid. A warning will
be output if the code is not valid. The sequence is
the same for "Generic" and "Personal" door opener
codes: press
The following will appear on the display:
LOCK REL. CODE
The lock will be operated and the following message
will appear if the code is correct:
User
CALL TO:
Switchboard
CODE NOT
VALID
button before entering each door
followed by the door opener code.
****
27
Werbung
