Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Editing data
The data related to the entered users can be edited
in this sub-menu. The following search criteria can
be applied:
• search by position in table (1-250)
• search by name.
The following message will appear on the display:
Modify Data
Search by Pos.
Modify Data
Search by Name
Press the scroll arrows to select the search criteria
and press
to confi rm.
Search by position
This sub-menu can be used either to edit the user
code, name or door opener code in a certain position
in the table or to delete the record. The following
message will appear on the display:
Position:
1
Code:
1001
Press the scroll arrows to select the position to be
edited and press
to confi rm. At this point, you can:
• delete the record by pressing
(or bs on
the keyboard 1032/65 to delete the code). A
confi rmation prompt will appear and the record
will be deleted.
• change the user code: enter a new code and
press
to confi rm and go to the next name to be
edited.
• change the name: a form similar to that for
entering names will appear to edit the user code.
Edit the name and press
to confi rm the
operation.
• change the user door opener code: a form similar
to that for entering door opener codes will appear
after editing the name. Edit the code and press
to confi rm the operation.
Search by name
This sub-menu can be used to edit a name or door
opener code associated to a record.
The following message will appear on the display:
Rossi Mario
Code:
1001
24
Press the scroll arrows to select the position to be
edited and press
to confi rm. At this point, you
can:
• change the name: edit the name and press
confi rm.
• change the user door opener code: a form similar
to that for entering door opener codes will appear
after editing the name. Edit the code and press
to confi rm the operation.
↓
Clear all
This sub-menu can be used to clear the name
table with respective user codes and personal door
opener code.
The following message will appear on the display:
↑
Are you sure?
<YES> <NO>
Press the scroll arrows to select and press
confi rm.
Association
The door phone programming sequence consists of
two steps:
A. Door phone booking (to be made on a calling
station)
B. Door phone programming (to be made in the
apartments).
A: Door phone booking.
Select the Association menu.
The following message will appear on the display:
Position:
C:1001
Associate?
1
Scroll the record list with the scroll arrows.
Press
to confi rm the records to be added to
the booking list. Symbol
the position. Press
instead of
a record from the booking list. Symbol
disappear.
2
The door phones can be programmed in the
same order after creating the booking list. Press
. The following will appear on the display:
MODULE BEING
PROGRAMMED
Proceed by programming the door phones.
B: Door phone programming.
1
Go to the fi rst booked user, hold the button
pressed and lift the door phone handset. Two
to
confi rmation beeps will be heard and the
LED will fl ash to indicate that it has been
programmed.
2
Go to the other booked users and repeat the
operations.
Refer to the attached sheet to remember the code/
button association sequence.
SEQUENZA DI ASSOCIAZIONE
SEQ.
NOMINATIVO
USER NAME
1
2
3
4
5
The entire operation (booking and programming)
to
must be repeated for each module in the system,
unless the "Clone" function (see below) is used.
The module will quit programming mode for the
following events:
• end of door phone programming
• 10 minute time-out after the last operation
• pressing the red programming button
• pressing any module key and entering the
programming password.
How to associate 2/3 door phones in parallel in 2nd
edition systems.
To install two or three door phones in one apartment
1
and make them both ring when a call is received,
press
related to the user twice or three times with
the door phones in parallel when booking the door
phones. When you reach the apartment where the
parallel door phones are installed according to the
programming sequence, repeat the programming
sequence on both door phones.
will appear next to
How to associate 2 door phones in parallel in 2nd
to delete
edition systems.
will
To install two door phones in one apartment and
make them both ring when a call is received,
press
related to the user twice times with the
door phones in parallel when booking the door
phones. When you reach the apartment where the
parallel door phones are installed according to the
programming sequence, repeat the programming
sequence on both door phones.
Using the "clone" function in 1st edition systems.
A single association between calling station codes
and respective door phones can be made in 1st
edition systems without switchboard and without
DS1072-026A
DS1072-026A
door open signal function. The remaining call
stations can be clones of the fi rst station (the master
station) and copy the codes associated to the single
users. To enable this function:
• defi ne the master station as address "1" (where
• defi ne all other stations as address "15".
Obviously, all names must be programmed on the
"clone" stations.
Edit password
This menu can be used to edit the password for
ASSOCIATION SEQUENCE
accessing module programming.
The following message will appear on the display:
N° DELLA POSTAZIONE (ID):
CALL MODULE NUMBER (ID):
PULSANTE / CODICE
PIANO
VARIE
PUSHBUTTON / CODE
FLOOR
VARIOUS
Enter the new 4-digit password and press
confi rm.
Switchboard call enable
This menu is used to enable direct concierge
switchboard calls simply by pressing
is only active when the door phone is in day mode.
The following message will appear on the display:
Press the scroll arrows to select and press
confi rm.
DEFAULT PROGRAMMING
The device is pre-programmed as follows:
System type:
Station type:
Code format:
Station number:
Off-hook waiting time: 20s
Busy time:
Door opener time:
To restore default settings:
• Disconnect module power.
• Hold the red programming button pressed and
• Hold the button pressed for approximately 10
• Release the button.
PROGRAMMING VIA PC
The call module can be programmed and confi gured
rapidly by means of a PC connected to the serial
port (8) of the call module by means of a special
to make the association).
Password:
9999
New:
. The function
Call key
<YES> <NO>
2nd edition
main
numeric (0001–9999)
1
20s
pulse
power up the module.
seconds and wait for a tone.
to
to
25
Werbung
