urmet domus BiBus II ED. 1072/13 Bedienungsanleitung Seite 12

case of 1st edition systems, the module will be
automatically confi gured as a main station and
should not be changed.
The following message will appear on the display:
C. MOD. TYPE:
<MA.> <SEC>
Press and to select and press to confi rm.
The system will automatically go back to the main
menu after a confi rmation tone.
1st edition system: this programming is not required.
Station number (ID)
A number from 1 to 12 is assigned to each main
calling station. A number from 0 to 9 is assigned to
each secondary station. The secondary number is
in the range from A to J in systems with alphabetic
prefi x. A to J programmed on a secondary station
will automatically be reprogrammed as a prefi x code
format. ID from 0 to 9 on a secondary station will
automatically be reprogrammed as a numeric code
format.
The following message will appear on the display:
== Station n°
Station 1
Enter the station number and press to confi rm.
Press to cancel the entry. The system will
automatically go back to the main menu after a
confi rmation tone.
1st edition system: the station number must be in
the range from 1 to 12 (there are no secondary
stations in the system). Assign 15 as station number
to use the clone function.
Busy time
The busy time is split into two sub-menus.
The following message will appear on the display:
== BUSY TIME
PICKUP TIME
== BUSY TIME
BUSY TIME
22
Press and to select the sub-menu and press
to confi rm.
Off-hook stand-by time
The off-hook stand-by time is the maximum time
of a call in which the user can answer the door
phone. All other calling stations will be busy during
this time. All devices in the system must have the
same off-hook waiting time. The following message
will appear on the display:
PICKUP TIME:
<10><20><30><40>
Press and to select and press
The system will automatically go back to the main
menu after a confi rmation tone.
Minimum conversation time (busy)
When a user is called and answers the door
phone, all other call stations will be busy for
the minimum programmed conversation time. A
communication that has just started cannot be
interrupted. All devices in the system must have the
same minimum conversation time (busy time). The
following message will appear on the display:
==
BUSY TIME:
<10><20><30><40>
Press and to select and press
The system will automatically go back to the main
menu after a confi rmation tone.
Door lock activation time
The relay controlling the door lock can be managed
in pulse mode (approximately 500 ms) or stabile
mode (from 1 to 30 s). The following message will
appear on the display:
= Door op. time
0 seconds
==
↓
Enter the number of seconds and press
confi rm. Press to cancel the entry. The system
will automatically go back to the main menu after a
confi rmation tone.
==
↑
Door opener codes
The eight generic door opener codes can be stored
in sequence.
The following message will appear on the display:
Lock rel. codes
1° Code:
Enter the 4-digit code and press
to cancel the entry. The second code can be
entered automatically after a confi rmation tone. The
system will automatically return to the main menu at
the end of programming. Alternatively, press
20S
three seconds to go back to the main menu.
Code type
The module can be used to call users with
numeric codes (0001-9999), alphanumeric codes
to confi rm.
with alphabetic prefi x (x000-x999) and alphanumeric
codes with alphabetic suffi x (000x-999x). Letters
from A to J can be used.
The following message will appear on the display:
= Code Type
Num.
= Code Type
Pref. x000.x999
20S
= Code Type
to confi rm. Suf. 000x.999x
Press and to select the code type and press
to confi rm.
Codes/names
The names and
programmed in this menu. The following message
will appear on the display:
=
= Code/Name
Enter Data
to
= Code/Name
Modify Data
= Code/Name
Clear All
DS1072-026A DS1072-026A
Press
to confi rm.
Enter data
The user codes and respective names and personal
door opener codes can be programmed in this sub-
menu.
to confi rm. Press
The fi rst free position in the 250 item table will
appear (one item for each user):
for Position:
Code:
Enter the numeric or alphanumeric code formed
by a variable number of digits from 1 to 4 and
press
for longer than three seconds to go back to the
previous menu. The same code can be entered in
two or three positions in an apartment where two
=
or three door phones are connected in parallel (you
↓ are advised to use adjacent positions to simplify
1.9999
the association). The following will appear on the
display after entering the code:
= Code 1001
↓↑
The name can be entered later. In this case, press
=
and enter the new code. Proceed as follows if the user
↑
name is known. Press
keypad to seek the required character. Select the
character. The cursor will shift right by one position to
enter a new character after approximately one second
if no other button is pressed. Press
last entered character. Use programming keyboard
1032/65 to considerably facilitate entry of names.
The same name can be assigned to different codes.
respective codes can be
Enter the name and press
door opener code. The following message will
appear on the display:
=
Code Lock rel.
↓
=
Enter the personal door opener code and press A
↓↑
to confi rm. The general code programmed during
the "Door opener code" phase cannot be entered.
Press
a door opener code to the user.
=
↑
and to select the sub-menu and press
1
to confi rm. Press to correct. Press
Name:
and on the call module
to delete the
to enter the respective
without entering a code to skip assigning
23