urmet domus BiBus II ED. 1072/13 Bedienungsanleitung Seite 10

CALL MODULE WITH DIRECTORY 2ND EDITION
1072/13 CAN BE USED TO RETROFIT OLD 1ST
EDITION SYSTEMS.
IN A SECOND EDITION SYSTEM (IMPLEMENTING
ALL BIBUS 2ND EDITION FEATURES) ALL
DEVICES ARE 2ND EDITION DEVICES AND THUS
CONFIGURED.
PERFORMANCE
• Two-module SINTHESI range: with back-lit
16x2-character LCD display, integrated speaker
and back-lit buttons.
• Direct user call by entering numeric code.
• Direct user call by entering alphanumeric code
connecting optional alphabetic keyboard
Ref.1038/74. Codes can have letter prefi xes or
suffi xes with letters A-J.
• User calls by selecting stored names (max. 250).
• Direct concierge switchboard call (day mode only)
by pressing button only (where confi gured).
• Management of 250 names with respective 4-digit
door opener code.
• Management of additional 8 generic door opener
codes with time bands using external clock.
• The module can be programmed by means of a
keyboard, programming keyboard 1032/65 or PC.
• Direct lock management by capacitance discharge
and hold current with programmable activation
time from 1 to 30s.
• Programmable door phone hang-up waiting time
(10s, 20s, 30s, 40s).
• Programmable minimum guaranteed conversation
time (10s, 20s, 30s, 40s).
• Maximum conversation time: 250s.
• Open door contact input.
• Hall button timed input.
• Mail key input.
• Acoustic call sent signal.
• Busy function signalled by message on display.
• Two
trimmers for adjusting speaker
microphone volume.
• One trimmer for adjusting display contrast.
• Optoisolated control signal management for video
door phone systems.
• Multilingual message display without additional
EEPROM.
• Powered by 9000/230 (12Vac).
18
STRUCTURE
The call module with directory consists of the
following parts:
1 2 3
1 2 3
4 5 6
7 8 9
X 0
and
1 Two-module Sinthesi front.
2 PC wire connector (CNS).
3 Adjustable call module microphone volume.
4 Adjustable call module speaker volume.
5 Programming button (for use only when
password is not known).
6 Programming alphanumeric keyboard (1032/65)
connector (CNP).
7 Alphanumeric display, two-rows, 16-characters,
back-lit.
8 Yellow back-lit name selection buttons.
9 Green back-lit number pad buttons with yellow
back-lit function buttons: "Cancel", "Key" and
"Call".
10
11
L2 L1 GND PA SP
MP2
4
5
CONTR.
6
12
7
13
8
9
10 Additional alphanumeric keyboard (1038/74)
connector.
11 Extractable connection terminal boards (MP2,
MV1, MS1).
12 Adjustable LCD contrast.
13 Extractable connection terminal board (MP1).
DESCRIPTION OF TERMINALS AND
CONNECTORS
MP1 terminal board
~0 Power 12Vac
~12 Power 12Vac
+T Back-up power positive
GND Back-up power negative
SE1 Electrical lock connection
SE2 Electrical lock connection
DS1072-026A DS1072-026A
MP2 terminal board
L1 Bus line 1st wire
L2 Bus line 2nd wire
GND Reference electrical earth
PA Hall door opener button input
SP Open door sensor contact input
MV1 terminal board
SN Video power unit on signal for video systems
SN R R1 H P GND +EP DT
R Video switching enable signal for video systems
MV1 MS1
R1 Video power earth
Sch./Ref. 1072/13
Data:.................... MS1 terminal board
H Door opener code time band contact input
P Mail key input
GND Reference electrical earth
+EP Auxiliary device power
DT Not used
CNA Alphabetic keyboard connector 1038/74
CNP Programming keyboard connector 1032/65
~0
CNS PC serial line connector
~12
+T
GND
TECHNICAL SPECIFICATIONS
Power:
SE1
Stand-by consumption:
SE2
Maximum consumption:
R signal:
MP1
Lock hold current:
Working temperature range: -10 +50°C
Humidity:
(*) with alphabetic keyboard connector 1038/74
INSTALLATION
Refer to the "technical manual" for instructions for
installing the call module. The module is programmed
by default with a jumper between the earth and
the "SP" signal to simulate the door closed contact.
Remove the jumper and connect the sensor between
GND and SP when the open door contact is required.
Connect the electrical lock positive to terminal SE1
and the negative to terminal SE2 when polarised
electrical locks are used.
12Vac nominal
300mAac max.
600mAac max. (*)
Imax = 80mA
190mA max.
90% RH @ 30°C
19