Werbung
◾
Do not operate the machine on excessively steep
EN
slopes. This reduces the risk of loss of control, slipping
and falling which may result in personal injury.
◾
When working on slopes, always be sure of your
footing, always work across the face of slopes,
never up or down and exercise extreme caution
when changing direction. This reduces the risk of
loss of control, slipping and falling which may result in
personal injury.
◾
Keep all parts of the body away from the cutter,
line or blade when the machine is operating.
Before you start the machine, make sure the cutter,
line or blade is not contacting anything. A moment
of inattention while operating the machine may result in
injury to yourself or others.
◾
Do not operate the machine above waist height.
This helps prevent unintended cutter or blade contact
and enables better control of the machine in unexpected
situations.
◾
When cutting brush or saplings that are under
tension, be alert for spring back. When the tension
in the wood fibres is released, the brush or sapling may
strike the operator and/or throw the machine out of
control.
◾
Use extreme caution when cutting brush and
saplings. The slender material may catch the blade and
be whipped toward you or pull you off balance.
◾
Maintain control of the machine and do not touch
cutters, lines or blades and other hazardous
moving parts while they are still in motion. This
reduces the risk of injury from moving parts.
◾
When clearing jammed material or servicing the
machine, make sure the switch is off and the
battery pack is removed. Unexpected starting of the
machine while clearing jammed material or servicing may
result in serious personal injury.
◾
Carry the machine with the machine switched
off and away from your body. Proper handling of the
machine will reduce the likelihood of accidental contact
with a moving cutter, line or blade.
◾
Only use replacement cutters, lines, cutting heads
and blades specified by the manufacturer. Incorrect
replacement parts may increase the risk of breakage and
injury.
◾
Damage to Trimmer - If you strike a foreign object
with the trimmer or it becomes entangled, stop the tool
immediately, check for damage and have any damage
repaired before further operation is attempted. Do not
operate with a broken guard or spool.
8
LINE TRIMMER ATTACHMENT — STA1600
◾
If the equipment should start to vibrate abnormally,
stop the motor and check immediately for the
cause. Vibration is generally a warning of trouble. A loose
head may vibrate, crack, break or come off the trimmer,
which may result in serious or fatal injury. Make sure
that the cutting attachment is properly fixed in position.
If the head loosens after fixing it in position, replace it
immediately. Never use a trimmer with a loose cutting
attachment.
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
◾
Use only with battery packs and chargers listed in
fig.A.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
Cutting Mechanism
Line Diameter
Cutting Width
Maximum Speed
Weight (Without battery pack)
Recommended Operating
Temperature
Storage Temperature
Measured sound power level L
WA
Sound pressure level at operator's
ear L
PA
Guaranteed sound power level L
(measured according to
2000/14/EC)
Front-assist handle
Valuation of
vibration a
h
Rear handle
◾
The above parameters are tested and measured
equipped with power head PH1420E.
Bump Head
2.4 mm nylon
twist line
40 cm
4900/5800 min
-1
1.53 kg
0°C-40°C
-20°C-70°C
95.72 dB(A)
K=0.77 dB(A)
81.6 dB(A)
K= 3 dB(A)
WA
96 dB(A)
2.5 m/s
2
K=1.5 m/s
2
1.8 m/s
2
K=1.5 m/s
2
Werbung
