Makita PV301D Betriebsanleitung Seite 10

Installing abrasive disc
Optional accessory
CAUTION:
Only use the twist-on/twist-off
system discs for sanding.
Disc selection
CAUTION:
The outside diameter of accessory
must be within the capacity rating of the power
tool.
CAUTION:
The rated speed of accessory
must be equal or higher than the maximum speed
marked on the power tool.
Always use the correct sized wheel that is made from
appropriate abrasive materials with the right grit size for
your job.
Abrasive disc materials
Abrasive materials Basic features
Aluminum Oxide Best for steel,
stainless steel
and metals. Single
crystal abrasive
material with
high tenacity and
durability.
Alumina Zirconium Best for INOX and
metals. Extremely
sharp and hard
abrasive material
with high durability.
Ceramic Best for INOX,
metals and non-fer-
rous materials.
Extremely sharp
and high resistant
to shock/heat/
wear.
Grit size
Grit
24/36 (coarse)
60/80
120 (fine)
Installing and removing abrasive disc
CAUTION:
Make sure that the twist-on/twist-
off pad is secured properly. Loose attachment will
run out of balance and cause an excessive vibration
which may cause loss of control.
Remove all dirt and foreign matter from the twist-on/
twist-off pad. Thread an abrasive disc onto the twist-on/
twist-off pad while pressing in the shaft lock. Hand
tighten securely.
To remove the abrasive disc from the twist-on/twist-off
pad, follow the installation procedure in reverse.
► Fig.10: 1. Abrasive disc 2. Twist-on/twist-off pad
Practical
applications
Fast sanding
Most metal jobs
Removing paint
from cars and
boats, etc.
General metal work
Practical applications
Heavy stock removal
Medium stock removal
Finishing
OPERATION
CAUTION:
Only use Makita genuine pads for polishing.
CAUTION:
Only use Makita genuine abrasive
disc for sanding (optional accessories).
CAUTION:
Make sure the work material is secured
and stable. Falling object may cause personal injury.
CAUTION:
Hold the tool firmly with one hand
on the switch handle and the other hand on the
side grip when performing the tool.
CAUTION:
Do not run the tool at high load over
an extended time period. It may result in tool malfunc-
tion which causes electric shock, fire and/or serious injury.
CAUTION:
Be careful not to touch the rotating part.
CAUTION:
Before operating the tool, make sure
that the side grip or caps are not loose. If the side grip or
caps are loose, the front cover may fall and cause an injury.
NOTICE:
Never force the tool. Excessive pressure
may lead to decreased polishing efficiency, damaged
pad, or shorten tool life.
NOTICE:
Continuous operation at high speed
may damage work surface.
General operation
► Fig.11
1.
Make sure that the workpiece is properly sup-
ported and both hands are free to control the tool.
2. Hold the tool firmly with one hand on the switch
handle and the other hand on the side grip.
3. Turn the tool on, letting the wheel reach full speed,
and then carefully enter into operation moving the tool
forward over the workpiece surface.
4.
Having finished, switch the tool off and wait until the wheel
has come to a complete stop before putting the tool down.
Polishing operation
► Fig.12
1. Surface treatment
Use a wool pad for rough finishing then use a sponge
pad for fine finishing.
2. Applying wax
Use a sponge pad. Apply wax to the sponge pad or work
surface. Run the tool at low speed to smooth out wax.
CAUTION:
Do not apply excessive wax or
polishing agent. It will generate more dust and may
cause eye or respiratory diseases.
NOTE: First, perform a test waxing on an inconspicu-
ous portion of the work surface. Make sure that the tool
will not scratch the surface or result in uneven waxing.
3.
Removing wax
Use a sponge pad. Run the tool to remove wax.
4. Polishing
Apply a sponge pad gently to the work surface.
10 ENGLISH