VOLTCRAFT CPAS-2400 Bedienungsanleitung Seite 2

OPERATING INSTRUCTIONS
USB CAR CHARGER
ITEM NO.: 1362459 CPAS-2400
ITEM NO.: 1362460 CPAS-2400/2+
INTENDED USE
The product is suitable for charging and operating one USB device (order no. 1362459) or two
USB devices (order no. 1362460) inside a vehicle. Power is supplied via an on-board voltage
socket. The product features overload and short circuit protection mechanisms. Use the
product in dry indoor areas only.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be
damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric
shock etc. Read the instructions carefully and keep them. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• USB car charger
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in theses operating instructions, we assume no liability
for any resulting personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Always turn off the connected device before connecting/disconnecting it.
• Unplug the product while it is not in use.
• The product gets hot during use. Ensure sufficient ventilation and never cover the
product during use.
• Do not short-circuit the USB outputs.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. Allow the
device to reach room temperature before connecting and using it. This may take
several hours.
• Never leave the product and the connected device unattended during use.
b) Miscellaneous
• Consult a professional if you require assistance with product operation, safety or
connection.
• Maintenance work, adjustments and repairs may be carried out only by a
professional or at a specialist workshop.
Should you have questions concerning correct product connection or operation, or should
other questions arise that this user manual does not address, please do not hesitate to
contact our technical support or a third-party professional.
OPERATION
Always turn off the desired device before connecting it to the USB port.
Make sure the connection is correct. If the product is not connected properly,
it could overheat or cause an electric shock or fire.
Make sure that your device meets the product's power requirements
(see technical data).
VERSION 08/15
If the product features more than one USB port, you can charge or operate several
devices at the same time. How to connect a single USB device is described below.
The current output of one single USB port must not exceed 2400 mA.
1. Connect the switched-off USB device to the product.
2. Plug the product into your vehicle's on-board voltage socket. The power indicator on the
product lights up to indicate the product is operational.
3. Your USB device is now charging. Should you wish to operate the USB device, you may
turn it on now.
4. Turn off the USB device before you disconnect the product from your vehicle's on-board
voltage socket.
5. Unplug the product from your vehicle's on-board voltage socket after use.
You can operate the product while the engine is both on or off. However, avoid starting
the engine while the product is connected as this cuts power to the voltage socket
briefly (this may not apply to all vehicle models). If the engine is switched off, drawing
current over a longer period of time will discharge the vehicle battery.
CLEANING
Disconnect the product from the on-board voltage socket before cleaning. Clean the product
with a dry, fiber-free cloth.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product in accordance with applicable
regulatory guidelines.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TECHNICAL DATA
Input voltage ................................................ 12 - 24 V/DC
Output voltage/ current ................................ 5 V/DC, 2400 mA (Item no.: 1362459)
Operating conditions .................................... 0 to +35 ºC, 20 – 90 % RH (non-condensing)
Storage conditions ....................................... -20 to +60 ºC, 10 – 90 % RH (non-condensing)
Dimensions (W x H x D) .............................. 30 x 29 x 66 mm (Item no.: 1362459)
Weight ......................................................... 22 g (Item no.: 1362459)
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2015 by Conrad Electronic SE
5 V/DC, 2 x 2400 mA (Item no.: 1362460)
48 x 29 x 71 mm (Item no.: 1362460)
40 g (Item no.: 1362460)
V1_0815_02-ETS-Mkde