Radiodetection RD8000 Bedienungsanleitung Seite 10

3. Press the key (locator) or the key (transmitter) to enter the BT menu.
4. Scroll up or down to the OFF option.
5. Press the key to switch Bluetooth off and return to the previous menu.
Pairing to a transmitter
To pair to a transmitter you require a Bluetooth enabled model such as the Tx-5B or Tx-10B.
Before you begin, you may choose to switch off all nearby Bluetooth equipment as they
may interfere with the locator and transmitter's pairing process.
On the locator:
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or
3. Press the key to enter the BT menu.
Scroll to the PAIR menu and press the
4.
5. Scroll to the BT-TX option.
NOTE: You must complete the pairing process within 90 seconds to prevent the
locator's Bluetooth connection from timing out.
On the transmitter:
6. Press the key to enter the menu.
7. Scroll to the BT menu using the or
8. Press the key to enter the BT menu.
9. Scroll to the PAIR option.
Starting the pairing process:
10. Press the key on the transmitter followed by the
press these keys within a 30 second window otherwise the connection may time out.
11. The transmitter and the locator will now attempt to pair.
When pairing is in progress, the transmitter and locator will display a flashing Bluetooth
icon. Pairing can take up to a minute. If the pairing process is successful, the transmitter
will display the icon and the locator will display a persistent Bluetooth icon for the
duration of the connection.
If pairing fails, ensure that any nearby Bluetooth devices are switched off or invisible then
repeat the process.
Once the locator and transmitter have successfully paired you can use iLOC to change
the transmitter's output frequency and power levels remotely from the locator.
keys.
key to enter it.
keys.
key on the locator. You must
18
Pairing to a PDA or PC
Connection requirements:
• Any RD8000 locator.
• A compatible Bluetooth enabled PDA or Bluetooth enabled PC or Laptop.
NOTE: The procedure below describes the pairing process between a RD8000
locator and a PDA. Pairing to a PC follows the same steps for the RD8000 locator
and similar steps for your PC or laptop. Consult your PC or laptop Bluetooth pairing
instructions to pair with the RD8000 locator.
Pair the RD8000 locator to your PDA using your PDA's Bluetooth software.
NOTE: The procedure for pairing your PDA may differ depending on the PDA make
and model. The following procedure should apply to most PDAs.
On the locator:
1. Press the key to enter the menu.
2. Scroll to the BT menu using the or
3. Press the key to enter the BT menu.
4. Scroll up or down to the PAIR menu.
5. Press the key to enter the PAIR menu.
6. Scroll up or down to the BT-PC option.
7. Press the key and the locator will attempt to pair with your PDA.
On your PDA:
8. From the PDA's Start menu, select Settings then select the Connections Tab
followed by the Bluetooth icon.
9. Ensure the Bluetooth radio is switched on and make the PDA visible to other devices.
10. Select the Devices tab and scan for new partnerships.
11. Create a partnership with the RD8M_xxx device.
12. If asked for a passkey, enter 1234.
13. Select the COM Ports tab and make a New Outgoing Port with the RD8000 locator.
Note the port number of the selected COM port.
Troubleshooting
Successful wireless communication depends on a number of factors including:
battery life, electromagnetic interference, device memory and physical obstructions.
Ensure that the RD8000 transmitter, locator and any other wireless device is sufficiently
charged for wireless communication. Note that many PDAs will suspend wireless
connections when their battery capacity drops below a threshold percentage. Consult
your device's documentation for more information.
keys.
19